Tài liệu Max Flow

Tài liệu Max Flow

Tài liệu Max Flow

... edge's flow ≤ edge's capacity. • Local equilibrium: inflow = outflow at every vertex (except s and t). Def. The value of a flow is the inflow at t. Maximum st -flow (maxflow) problem. Find a flow ... forward edge empty backward edge A Maxflow-mincut theorem Augmenting path theorem. A flow f is a maxflow iff no augmenting paths. Maxflow-mincut theorem. Value of the maxflow =...

Ngày tải lên: 25/12/2013, 10:48

71 299 1
Tài liệu controlling flow in PL / SQL pdf

Tài liệu controlling flow in PL / SQL pdf

... TEXT_IO.PUT_LINE(TO_CHAR(:x)); 6.Repeat steps 4 and 5 using values 150 and 10. Controlling Flow in PL/SQL Blocks 23Ć3 Objectives You can control the flow of your PL/SQL block by using conditional statements and loops. At ... ’YES’; –– Leave inner loop only END LOOP Inner_Loop; END LOOP Outer_loop; END; Controlling Flow in PL/SQL Blocks 23Ć29 Summary Control PL/SQL logic with the c...

Ngày tải lên: 21/12/2013, 06:17

34 343 0
Tài liệu Compressible flow friction docx

Tài liệu Compressible flow friction docx

... investigations of gas flow in pipelines it can be conclude that we can found all 5 flow resistance zones in steel gas pipe network. Table .Flow regimes in gas networks, in % Flow regime zones Minor ... Coefficient λ • In pipelines of gasses flow functional reliance λ = f(∆ e ,Re) is valid.It means ,that friction depend from the equivalent roughness and flow regime. • For stee...

Ngày tải lên: 22/12/2013, 21:18

14 207 0
Tài liệu Compressible Flow Intro_L8_1 doc

Tài liệu Compressible Flow Intro_L8_1 doc

... principle dA = 0 → Ma = 1 Flow Flow Flow Flow Flow Regime Sub sonic Ma < 1 Super sonic Ma > 1 Nozzle Diffuser dp<0 dV x >0 dp>0 dV x <0 Compressible Flow Intro_L8_2 What do ... Temperature will be in absolute unit, eg Kelvin Flow Classification: - Subsonic: Ma < 1 - Supersonic: Ma > 1 - Hypersonic: Ma > 5 Density becomes a flow variable and Temper...

Ngày tải lên: 22/12/2013, 21:18

11 184 0
Tài liệu Controlling flow in PL / SQL pptx

Tài liệu Controlling flow in PL / SQL pptx

... v_counter > 10; END LOOP; . . . Controlling Flow in PL/SQL Blocks 23 Introduction to Oracle: SQL and PL/SQL Using Procedure Builder23Ć20 Controlling Flow in PL/SQL Blocks 23Ć21 Loop Statements ... IF; END calc_val; Introduction to Oracle: SQL and PL/SQL Using Procedure Builder23Ć12 Controlling Flow in PL/SQL Blocks 23Ć13 Building Logical Conditions Build a simple Boolean condition b...

Ngày tải lên: 17/01/2014, 09:20

34 353 0
Tài liệu Max speed FireFox 1 pdf

Tài liệu Max speed FireFox 1 pdf

... phần mềm chuyên dụng để phục hồi và khai thác lại các dữ liệu đó. Có rất nhiều chương trình có thể giúp bạn thực hiện việc xoá dữ liệu an toàn nhưng khi bạn sử dụng qua chương trình Erase ... Lưu ý là trong quá trình cài đặt, chương trình sẽ yêu cầu kết nối internet để có thể liên kết dữ liệu với trang chủ. 2. Chọn chủ đề cho thiệp: Giao diệ n chính của Hallmark CardStudio gồm men...

Ngày tải lên: 22/01/2014, 01:20

7 264 0
Tài liệu flower_2 ppt

Tài liệu flower_2 ppt

... $ Flower Copyright 1998-99 Stephen Hecht. All Rights Reserved A dollar bill produces a model 100mm long with a bloom of 40mm diameter. The bloom is adapted from Herman Lau’s Flower-in-a-Pot. ... Sink hexagonally halfway. (Open out to find landmarks.) C Alternate method, using Lau’s 8-petalled flower: 1. Crease at quarters. 2. Water-bomb base at one end. 3. Squash the 4 triangular flaps of ......

Ngày tải lên: 10/12/2013, 11:16

4 257 0
Tài liệu flowerwithleaves_2 docx

Tài liệu flowerwithleaves_2 docx

... Mod   el: Peter Budai © 1997. Dia ✁ grams: Peter Budai © 1998. Virág levelekkel Flower with leaves Flower with leaves ✂ V ✄ irág levelekkel 7. ☎ Összehajtjuk a már kész élek segítségével. Collapse

Ngày tải lên: 10/12/2013, 11:16

2 318 0
Tài liệu Đồ họa 3D STUDIO MAX pptx

Tài liệu Đồ họa 3D STUDIO MAX pptx

... Chơng trình đồ hoạ cơ bản 3d studio max Giáo trình đồ họa 3d studio max Sử dụng hệ tọa độ LOCAL COORDINATES No1: Khởi động chơng trình 3D Studio Max, sau đó vào File -> Reset. No2: ... bài: Nguyễn giang phone: 0989089680 Trang 10 Chơng trình đồ hoạ cơ bản 3d studio max Dới Align chọn Max, dới Output chọn Patch chúng ta sẽ đợc: No16: Mô hình chiếc cốc Martini đã hòan ....

Ngày tải lên: 11/12/2013, 23:15

23 374 2
w