Tài liệu Data Acquisition Basics Manual LabVIEW ppt

... acquisition with LabVIEW. Chapter 3 Basic LabVIEW Data Acquisition Concepts © National Instruments Corporation 3-3 LabVIEW Data Acquisition Basics Manual Locating the Data Acquisition VIs in LabVIEW You ... Corporation 3-1 LabVIEW Data Acquisition Basics Manual 3 Basic LabVIEW Data Acquisition Concepts This chapter explains key concepts in understand...

Ngày tải lên: 22/12/2013, 21:18

... LEDs Green Red Green Red Red Red Red Red Green Green Description Frame Ground Transmitte Data (+) Received Data (+) Request To Send Clear To Send Data Set Ready Signal Ground Data Carrier Detect Positive DC Test Voltage Negative ... black 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21...

Ngày tải lên: 10/12/2013, 17:15

... Guard enabled on a data center access switch. 1-2 Data Center: Securing Server Farms 956638 Chapter 1 Securing Intranet Server Farms: Overview Figure 1-1 Data Center Security and Data Center Networking The ... the data center environment. A collapsed, single layer data center architecture consists of two layers: aggregation and access (front-end). Figure 3-1 shows these data c...

Ngày tải lên: 21/12/2013, 06:16

... instruction set summary Data processing immediate shift shiftcond [1] RdRnS0 0 0 opcode shift amount Rm0 Data processing register shift [2] shiftcond [1] RdRnS0 0 0 opcode 1 Rm0Rs Data processing immediate ... a sequence of data memory accesses, or to their data sizes, or time order. This mechanism consists of IMPLEMENTATION DEFINED requirements on the memory accesses whose number...

Ngày tải lên: 22/01/2014, 00:20

... above Exceptions Data Abort Operation if ConditionPassed(cond) then data = Memory[address,1] Rd = SignExtend (data) Usage Used with a suitable addressing mode, LDRSB allows 8-bit signed memory data to ... above Exceptions Data Abort Operation if ConditionPassed(cond) then if address[0] == 0 data = Memory[address,2] else /* address[0] == 1 */ data = UNPREDICTABLE Rd = SignE...

Ngày tải lên: 22/01/2014, 00:20

... reserved. A5-9 5.1.5 Data- processing operands - Logical shift left by immediate This data- processing operand is used to provide either the value of a register directly (lone register operand, as described in Data- processing ... rights reserved. ARM DDI 0100E 5.1.3 Data- processing operands - Immediate This data- processing operand provides a constant (defined in the instruction) oper...

Ngày tải lên: 22/01/2014, 00:20

... Multiple instruction is being used for block data transfer, as it is likely that the Load Multiple and Store Multiple have the same addressing mode, so that the data is stored in the same way that ... and Store Multiple are being used to access a stack, the data is not loaded with the same addressing mode that was used to store the data, because the load (pop) and store (push) opera...

Ngày tải lên: 22/01/2014, 00:20

... reserved. ARM DDI 0100E 6.4 Data- processing instructions Thumb data- processing instructions are a subset of the ARM data- processing instructions, as shown in Table 6-2. All Thumb data- processing instructions ... execution: • For the Data Abort exception, the primary method of return causes execution to resume at the aborted instruction, which causes it to be re-executed. As descri...

Ngày tải lên: 22/01/2014, 00:20

... stack which the Thumb instruction set is designed to use, incrementing the SP is used to discard data on the top of the stack. Notes Alternative syntax This instruction can also be written as ADD

Ngày tải lên: 22/01/2014, 00:20