Tài liệu Route Optimization Challenge Lab doc

... 1 - 2 Semester 5: Advanced Routing v2.0 - Lab 7.6.1 Copyright  2001, Cisco Systems, Inc. 7.6.1 Route Optimization Challenge Lab 192.168.200.99/24 192.168.216.88/24 Fa0/0 192.168.200.1/24 Fa0/0 192.168.216.1/24 London ... end of the month. The only monies available for the project are for provisioning WAN links. Design Considerations You are to work with the existing rout...

Ngày tải lên: 21/12/2013, 19:15

... all routers. • Configure Dopey to be in a separate DECnet area from the rest of the routers. • Verify that you can DEC ping from any router to any other router. TIME: 45 minutes Lab ... Practice CCIE Lab V1.0GG SE Practice CCIE Lab Cisco Systems Internal Use Only 1 SE Practice CCIE Lab V1.0GG TIME: 30 minutes 2.11 BGP Route Filter...

Ngày tải lên: 11/12/2013, 14:15

... 1 - 2 Semester 5: Advanced Routing v2.0 - Lab 5.9.1 Copyright  2001, Cisco Systems, Inc. 5.9.1 OSPF Challenge Lab Lo 172.16.1.1 /24 S0/0 172.16.0.5 /30 S0/0 172.160.5 ... Instead of the administrative burden of many static routes, you want a stable default route advertised through OSPF, but you are concerned about route flapping if your WAN link to ISP2 is unstable. ... We...

Ngày tải lên: 11/12/2013, 15:15

... 1 - 2 Semester 5: Advanced Routing v2.0 - Lab 9.8.1 Copyright  2001, Cisco Systems, Inc. 9.8.1 BGP Challenge Lab SanJose1 SanJose3 SanJose2 Lo0 11.0.0.1/8 ISP2A ISP1A Lo0 ... to be readily available and reliable at all times. (The loopback addresses on the ISP1A and ISP2 routers represent other customers. The loopback addresses on the San Jose routers represent ... /30 Lo3 192.1...

Ngày tải lên: 24/01/2014, 19:20

... 1 - 2 Semester 5: Advanced Routing v2.0 - Lab 9.8.1 Copyright  2001, Cisco Systems, Inc. 9.8.1 BGP Challenge Lab SanJose1 SanJose3 SanJose2 Lo0 11.0.0.1/8 ISP2A ISP1A Lo0 ... to be readily available and reliable at all times. (The loopback addresses on the ISP1A and ISP2 routers represent other customers. The loopback addresses on the San Jose routers represent ... /30 Lo3 192.1...

Ngày tải lên: 24/01/2014, 19:20

Ngày tải lên: 11/12/2013, 14:15

... understand them. First we invoke LabVIEW by the path Start>>Programs>>Labview>>Labview. (If there is a LabVIEW icon on your screen you can also start LabVIEW by double-clicking on ... may provide you with a LabVIEW driver which appears as a VI representing the card and its functionality in the LabVIEW environment. You can also write a LabVIEW module using LabVIEW and presen...

Ngày tải lên: 22/12/2013, 02:16

... 12 that the control stays put. Move the label back. Now do the same to the control. Notice that the control and label move as one. The point is that moving a label moves it in relation to the control. ... control/indicator, not the label only!). An important aspect of LabVIEW programming is the concept of dataflow programming - things happen as the data for them are available, and by conventi...

Ngày tải lên: 18/01/2014, 14:20

... Techniques © James R. Drummond - September 1996 28 PHY 406 - Microprocessor Interfacing Techniques LabVIEW Tutorial - Part VI Error Handling Handling Errors Before I show you how to connect an error ... root” is a reasonable example and one which will avoid an error if we cope with it properly. In LabVIEW we can use a case construct to take care of this. A case construct consists of a number

Ngày tải lên: 18/01/2014, 14:20

... Techniques LabVIEW Tutorial - Part VII Wrapping It Up - SubVIs Hiding the Hard Work Encapsulation or the enclosing of a body of work into a sub-VI is an important part of serious LabVIEW programming. ... sub-VI. Now pop-up on the icon again and select Show Connector. LabVIEW assigns a connector pattern to this VI. The general rule in LabVIEW is that inputs are on the left, outputs are on the...

Ngày tải lên: 18/01/2014, 14:20