Tài liệu ISDN and DDR pptx

Ngày tải lên: 21/12/2013, 19:15

... Protocol. gaddr Global address—An address set with the global and static commands. GRE Generic Routing Encapsulation protocol—Commonly used with Microsoft’s implementation of PPTP. HSRP Hot-Standby ... low-level TCP/IP protocol that maps a node’s hardware address (called a “MAC” address) to its IP address. Defined in RFC 826. An example hardware address is 00:00:a6:00:01:ba. (The first thre...

Ngày tải lên: 21/12/2013, 18:15

... B, and D are the three main functions of a layer-2 device. 5. C. During the learning function, the switch places addresses and ports in a CAM table—another term is port address table. ý A, B and ... CAM table and does not see the source MAC address (0000.0A01.AAAA), so it adds it along with port 1. It also examines the destination MAC address (0000.0A01.CCCC) and does not see this a...

Ngày tải lên: 21/12/2013, 19:15

... Editor: Editor: Đo Đo à à n Quang Minh n Quang Minh 1 1 C# and .NET Framework C# and .NET Framework Programming with Programming with Microsoft Microsoft .NET .NET Đo Đo à à n

Ngày tải lên: 22/12/2013, 19:17

... Cascaded Remote Physical Standby C-5 C.3.2 Local Physical Standby and Cascaded Remote Logical Standby C-5 C.3.3 Local and Remote Physical Standby and Cascaded Local Logical Standby C-6 C.3.4 Consolidated ... the logical standby database, using SQL interfaces. x QUOTA_SIZE and NOQUOTA_SIZE 12-34 QUOTA_USED and NOQUOTA_USED 12-37 REGISTER and NOREGISTER 12-39 REOPEN and NOREOPEN 1...

Ngày tải lên: 17/01/2014, 06:20

... fiction and urban space with me and pointed me in the direction of seminal films and literature, while Sylvie Blum-Reid read and commented on Chapter 3 on Paris with map in hand. Ewa Wampuszyc and ... industry, traffic, and masses of people, had disappeared and given way to a landscape of rubble and ruins. Shandley points out that “[b]ecause of the special place film held as a pr...

Ngày tải lên: 19/01/2014, 21:20

... provided in the mold – Leader pins and bushings (2, 3, or 4) – Leader pins and bushings between individual cavities and cores – Taper fits between individual cavities and cores – Taper fits between ... machines, provisions 6 and 7 are combined in one unit) 8. Provision for heating the plastic in the plasticizing unit 9. Cycle controls (sequencing logic, timers, etc.) and a command...

Ngày tải lên: 20/01/2014, 02:20

... Easy preparation and installation; installs just like a standard BNC with BNC tooling • Compatible with hex, square, and 12-point crimp tools and select competitive crimp tool and die sets • Tarnish-resistant, ... Dimensions Hand Crimp Tool Connector Die Set Center Crimp Ordering Number Ordering Number Conductor Sleeve Ordering Information Hand Crimp Tool WT-2 Ergonomic Handle WT-3 L...

Ngày tải lên: 24/01/2014, 11:20

... IP addressing Copyright  2003, Cisco Systems, Inc. Case Study: Routing 11 - 12 • The concept of reserved address space for routers, servers, and hosts • The reasons for developing an IP address ... Password VTY Password Serial 0/0 IP address Serial 0/1 IP address *Serial 0/0 Clock Rate *Serial 0/1 Clock Rate Fa 0/0 IP address Fa 0/1 IP address Enable the interfac...

Ngày tải lên: 24/01/2014, 19:20

... Ratings, Standard 210-74, Air Moving and Conditioning Association, Arlington Heights, IL, 1974. 55.1 PUMP AND FAN SIMILARITY The performance characteristics of centrifugal pumps and fans ... same basic laws and derived equations and, therefore, should be treated together and not separately. Both fluid machines provide the input energy to create flow and a...

Ngày tải lên: 27/01/2014, 16:20