Tài liệu Back-to-Back Frame Relay ppt

... Turn debug frame- relay packet off. Singapore#no debug frame- relay packet or no debug all 4. Based upon the map being dynamically established and output from the debug frame- relay packet ... determine whether a frame- relay map or frame- relay interface-dlci command was used in the router configuration? (Hint: Inverse ARP.) Since you have determined a fra...

Ngày tải lên: 11/12/2013, 14:15

... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b. What ... Berlin(config-router)#network 192.168.6.0 Step 7 Verifying Frame Relay PVC a. On the Amsterdam router, issue the command show frame- relay pvc: Amsterdam#show fra...

Ngày tải lên: 18/01/2014, 05:20

... Show frame- relay pvc Command Field Descriptions Field Description DLCI One of the DLCI numbers for ... this PVC Dropped Pkts Number of incoming and outgoing packets dropped by the router at the Frame Relay level In FECN Pkts Number of packets received with the FECN bit set In BECN Pkts

Ngày tải lên: 11/12/2013, 14:15

... address via a “static” frame- relay map statement. “CISCO” identifies the Frame Relay encapsulation used with frame- relay map statement, which is the default Frame Relay encapsulation on Cisco ... broadcast frame- relay lmi-type ansi Remove the incorrect frame- relay map statement. Singapore(config-if)#no frame- relay map ip 192.168.192.2 17 broadcast Reen...

Ngày tải lên: 11/12/2013, 14:15

... encapsulation frame- relay no ip mroute-cache cdp enable frame- relay interface-dlci 18 frame- relay lmi-type ansi As was discovered earlier, the encapsulation is frame- relay and the frame- relay ... information about each router. • show interface • show frame- relay lmi • show frame- relay pvc • show frame- relay map • debug frame- relay lmi G...

Ngày tải lên: 11/12/2013, 14:15

... 5.2.1 Configuring Frame Relay Objective • Configure a router to establish a connection to a local Frame Relay switch. Background/Preparation An Adtran Atlas550 Frame Relay emulator is used ... a. In Frame Relay, the customer router is considered the DTE device. In order to configure the serial interface the Layer 2 Frame Relay frame type must be defined. To config...

Ngày tải lên: 18/01/2014, 05:20

... Configuring Frame Relay PVC Objective • Configure two routers back-to-back as a Frame Relay permanent virtual circuit (PVC). This will be done manually, in the absence of a Frame Relay switch, ... the Frame Relay frame type to be used on this link. To configure the encapsulation type, use the command encapsulation frame- relay ietf. Disable keepalive messages sinc...

Ngày tải lên: 18/01/2014, 05:20

... Configuring Frame- Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate the switch /Frame Relay ... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterdam#...

Ngày tải lên: 18/01/2014, 05:20

Ngày tải lên: 11/12/2013, 14:15

... adaptive-shaping frame- relay bc frame- relay be frame- relay becn-response-enable frame- relay broadcast-queue frame- relay cir frame- relay class frame- relay custom-queue-list frame- relay de-group frame- relay ... frmr frame- relay lapf k frame- relay lapf n200 frame- relay lapf n201 frame- relay lapf t200 frame- relay lapf t203 frame- relay lm...

Ngày tải lên: 21/12/2013, 19:15