Tài liệu Lab 10 3 5d Subnetting a Class C Network docx

... Lab 10. 3. 5d Subnetting a Class C Network Objective The objective of this lab is to provide a subnetting scheme using a Class C network. Background / Preparation This is a written exercise ... written exercise and is to be performed without the aid of an electronic calculator. The Classical Academy has acquired a Class C address, 192.168.1.0. The a...

Ngày tải lên: 21/12/2013, 19:15

... 2 CCNA 1: Networking Basics v 3. 0 – Lab1 0 .3. 5.4 Copyright  20 03, Cisco Systems, Inc. Lab 10. 3. 5d Subnetting a Class C Network Objective Te objective of this lab is to provide a subnetting ... scheme using a Class C network. Background / Preparation This is a written exercise and is to be performed without the aid of an electronic calculator....

Ngày tải lên: 21/12/2013, 19:15

... scheme using a Class B network Background / Preparation This is a written lab and is to be performed without the aid of an electronic calculator. ABC Manufacturing has acquired a Class B address, ... 2 CCNA 1: Networking Basics v 3. 0 – Lab1 0 .3. 5 .3 Copyright  20 03, Cisco Systems, Inc. Lab 10. 3. 5c Subnetting a Class B Network Objective The obje...

Ngày tải lên: 21/12/2013, 19:15

Ngày tải lên: 21/12/2013, 19:15

... address classes • The default subnet masks 1 - 7 CCNA 1: Networking Basics v 3. 0 – Lab1 0 .3. 5a Copyright  20 03, Cisco Systems, Inc. • The number of networks that can be created with each class ... 3 - 7 CCNA 1: Networking Basics v 3. 0 – Lab1 0 .3. 5a Copyright  20 03, Cisco Systems, Inc. Step 4 One Class C network with subnets using a custom subnet mask This ex...

Ngày tải lên: 11/12/2013, 14:15

... 1: Networking Basics v 3. 0 – Lab1 0 .3. 5.1 Copyright  20 03, Cisco Systems, Inc. • The IP address classes • The default subnet masks • The number of networks that can be created with each class ... 1 - 7 CCNA 1: Networking Basics v 3. 0 – Lab1 0 .3. 5.1 Copyright  20 03, Cisco Systems, Inc. Lab 10. 3. 5a Basic Subnetting Objective • How to identify reasons to use...

Ngày tải lên: 21/12/2013, 19:15

... Control Panel and then click the Network Connection icon. • Select the Local Area Network Connection and click on Change settings of this connection. See the example below: 3 - 4 CCNA 1: Networking ... be accomplished using a cat 5 or 5e straight-through patch cable. Locate two cables that are long enough to reach from each PC to the switch. Attach one end to the NIC and the other...

Ngày tải lên: 11/12/2013, 14:15

... Use a mnemonic. • Describe the characteristics, functions and keywords relating to each layer. • Describe the packaging units used to encapsulate each layer. • Name the physical devices or components ... 1 - 2 CCNA 1: Networking Basics v 3. 0 - Lab 2 .3. 7 Copyright  20 03, Cisco Systems, Inc. Lab 2 .3. 7 OSI Model Characteristics and Devices Objective • Name the seven l...

Ngày tải lên: 21/12/2013, 19:15

... and a V .35 DTE cable will be used to simulate the WAN connection. d. V. 35 cable characteristics The V .35 DCE connector is a large female V .35 (34 -pin) connector. The DTE cable has a large male ... > Control Panel and then click the Network Connection icon. • Select the Local Area Network Connection and click on Change settings of this connection. • Select the TCP/IP p...

Ngày tải lên: 11/12/2013, 14:15

... - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 7 .3. 5 Copyright  20 03, Cisco Systems, Inc. Lab 7 .3. 5 Configuring IGRP Objective • Setup IP an addressing scheme using class C networks. ... Configure IGRP on routers. Background/Preparation Cable a network similar to the one in the diagram. Any router that meets the interface requirements displayed in the above...

Ngày tải lên: 11/12/2013, 14:15