Tài liệu Lab 1 2 4 Converting RIP v1 to RIP v2 pdf

... Systems, Inc. Lab 1. 2. 4 Converting RIP v1 to RIP v2 Objective • Configure RIP v1 on routers. • Convert to RIP v2 on routers. Background/Preparation Cable a network similar to the shown in ... FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 25 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 26 00 FastEthernet 0/0 (FA0/0) Fa...

Ngày tải lên: 21/12/2013, 19:15

... 3.0 - Lab 1. 2. 4 Copyright  20 03, Cisco Systems, Inc. Lab 1. 2. 4 Converting RIP Version 1 to RIP Version 2 Objective • Configure RIP Version 1 on routers. • Convert to RIP Version 2 on ... Serial 0 (S0) Serial 1 (S1) 17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 25 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial...

Ngày tải lên: 21/12/2013, 19:15

... Lab 1. 2. 5 Verifying RIP v2 Configuration Objective • Configure RIP v1 and v2 on routers. • Use show commands to verify RIP v2 operation. Background/Preparation Cable a network similar to ... RIP v1? ________________ c. What is the difference between RIP v2 and RIP v1? ________________________________ d. What must be done in order to see a differe...

Ngày tải lên: 11/12/2013, 13:15

... serial 0 BHM(config-if)#ip address 17 2 .16 .1. 2 255 .25 5 .25 5.0 BHM(config-if)#exit BHM(config)#interface fastEthernet 0 BHM(config-if)#ip address 17 2 .16 .3 .1 25 5 .25 5 .25 5.0 BHM(config-if)#exit BHM(config)#exit ... GAD from a class B (25 5 .25 5.0.0) to a Class C (25 5 .25 5 .25 5.0). Use the same IP address. GAD(config)#interface fastEthernet 0 GAD(config-if)...

Ngày tải lên: 11/12/2013, 13:15

... Routing v 3.0 - Lab 1. 2. 3 Copyright  20 03, Cisco Systems, Inc. b. Host connected to router BHM IP Address: 17 2 .18 .0 .2 Subnet mask: 25 5 .25 5.0.0 Default gateway: 17 2 .18 .0 .1 Step 21 Verify that ... address 17 2 .18 .0 .1 25 5 .25 5.0.0 BHM(config-if)#no shutdown BHM(config-if)#exit Step 17 Configure the IP host statements on router BHM BHM(c...

Ngày tải lên: 21/12/2013, 19:15

... 3.0 - Lab 1. 2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 1. 2. 6 Troubleshooting RIP v2 using Debug Objective • Configure RIP v2 on both routers • Use debug commands to verify proper RIP ... FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 25 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 26 00 FastEthernet 0/0 (FA0/0) FastEthernet...

Ngày tải lên: 21/12/2013, 19:15

... v 3.0 - Lab 1. 2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 1. 2. 6 Troubleshooting RIP Version 2 using Debug Objective • Configure RIPv2 on both routers • Use debug commands to verify ... (FA1) Serial 0 (S0) Serial 1 (S1) 25 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 26 00 FastEthernet 0/0 (FA0/0) FastEthernet 0 /1 (FA0 /1) Serial 0/0...

Ngày tải lên: 21/12/2013, 19:15

... FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1) 25 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 26 00 FastEthernet 0/0 (FA0/0) FastEthernet 0 /1 (FA0 /1) Serial 0/0 (S0/0) Serial 0 /1 (S0 /1) ... Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2 800 (806) Ethernet 0 (E0) Ethernet 1 (E1) 16 00 Ethernet 0 (E0) Ethernet 1...

Ngày tải lên: 11/12/2013, 13:15

... identified. Step 3 Locate the RJ -45 to DB-9 adapter 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1. 2. 5 Copyright  20 03, Cisco Systems, Inc. Lab 1. 2. 5 Connecting Console Interfaces ... 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1. 2. 5 Copyright  20 03, Cisco Systems, Inc. Step 1 Identify connectors and components a. Examine...

Ngày tải lên: 11/12/2013, 13:15

... 6 5 4 3 2 1 12 8 64 32 16 8 4 2 1 Position Value 12 8 20 7 12 8 64 79 64 8 15 8 4 7 4 2 3 2 1 The same conversion table and simple division can be used to convert binary values to decimal ... 32- bit binary form and dotted decimal form. Binary IP Address: 11 000000 .10 1 010 00.0 010 110 1. 011 110 01 Decimal IP Address: 19 2 .16 8...

Ngày tải lên: 11/12/2013, 13:15