Tài liệu Lab 1 1 9 Basic PC/Network Troubleshooting Process doc
Tài liệu Lab 3.1.9a Fluke 620 Basic Cable Testing doc
... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9a Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 9a Fluke 620 Basic Cable Testing
Objective
• Use ... that have already been made. Test them for basic continuity, breaks in
wires, shorts, two or more wires touching, using a basic cable tester. In future labs similar cables will
be created.
Simple ... cables will
be...
Tài liệu Lab 3.1.9b Fluke 620 Basic Cable Testing doc
... dollars. Advanced cable testers will be used in future labs to do wire
1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9b Copyright 2003, Cisco Systems, Inc.
...
Lab 3 .1. 9b Fluke 620 Basic Cable Testing
Objective
• Use a simple cable tester to verify whether a straight-thru ... cables will
be created.
Simple Cable Testers: There are a number of basic cable testers...
Tài liệu Lab 3.1.9b Fluke 620 Basic Cable Testing pptx
... dollars. Advanced cable testers will be used in future labs to do wire
1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9b Copyright 2003, Cisco Systems, Inc.
...
Lab 3 .1. 9b Fluke 620 Basic Cable Testing
Objective
• Use a simple cable tester to verify whether a straight-thru ... cables will
be created.
Simple Cable Testers: There are a number of basic cable testers a...
Tài liệu Lab 3.1.5 Configuring a Serial Interface pptx
...
Router 1
GAD
DCE 19 2 .16 8 .15 .1 255.255.255.0 class cisco
Router 2
BHM
DTE 19 2 .16 8 .15 .2 255.255.255.0 class cisco
2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 5 Copyright ...
__________________________________________________________________________
Step 10 Verify that the serial connection is functioning
a. ping the serial interface of the oth...
Tài liệu Lab 3.1.5 Series Circuits docx
... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright 2003, Cisco Systems, Inc.
Battery
Lab 3 .1. 5 Series Circuits
Switch
Bulb
... LEDs with resistors
• 6v lantern battery
2 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright 2003, Cisco Systems, Inc.
Step 1 Measure the Resistances of all devices
Measure the ... basic electrical circuit...
Tài liệu Lab 3.1.6 Making Configuration Changes doc
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 6 Making Configuration Changes
Objective
• Configure some basic router ...
password
Enable/VTY/Console
passwords
Gadsden
17 2 .16 .0 .1 255.255.0.0 Cisco1
3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc....
Tài liệu Lab 3.1.6 Making Configuration Changes ppt
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 6 Making Configuration Changes
Router ...
Enable
Secret
password
Enable/VTY/Console
passwords
GAD 19 2 .16 8 .14 .1 255.255.255.0 class cisco
Objective
• Configure some basic router settings.
• Bring interfaces up and down.
• Make ... HyperTerminal session...
Tài liệu Lab 3.1.7 Troubleshooting a Serial Interface doc
...
__________________________________________________________________________
Step 9 Verify that the serial connection is functioning by pinging the serial interface of the
other router
London#ping 19 2 .16 8 .15 .2
Paris#ping 19 2 .16 8 .15 .1
a. From London, ... the end of the lab to correctly identify the interface identifiers to be used
based on the equipment in the la...
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface docx
... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 7 Copyright 2003, Cisco Systems, Inc.
Lab 3 .1. 7 Configuring an Ethernet Interface
... on the type of router.
GAD(config)#interface fastEthernet 0
GAD(config-if)#ip address 19 2 .16 8 .14 .1 255.255.255.0
GAD(config-if)#no shutdown
GAD(config-if)#exit
GAD (config)#exit
Note: ... HyperTerminal session lab...
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface pptx
... Routing Basics v 3.0 - Lab 3 .1. 7 Copyright 2003, Cisco Systems, Inc.
Step 2 Configure the fastEthernet 0 interface
GAD(config)#interface fastEthernet 0
GAD(config-if)#ip address 19 2 .16 8 .14 .1 ...
Router 1
GAD
19 2 .16 8 .14 .1 255.255.255.0 class cisco
Objective
• Configure an Ethernet interface on the router with an IP address and a subnet mask.
Background/Pr...