... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9a Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 9a Fluke 620 Basic Cable Testing Objective • Use ... that have already been made. Test them for basic continuity, breaks in wires, shorts, two or more wires touching, using a basic cable tester. In future labs similar cables will be created. Simple ... cables will be...
Ngày tải lên: 11/12/2013, 13:15
... dollars. Advanced cable testers will be used in future labs to do wire 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9b Copyright 2003, Cisco Systems, Inc. ... Lab 3 .1. 9b Fluke 620 Basic Cable Testing Objective • Use a simple cable tester to verify whether a straight-thru ... cables will be created. Simple Cable Testers: There are a number of basic cable testers...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.9b Fluke 620 Basic Cable Testing pptx
... dollars. Advanced cable testers will be used in future labs to do wire 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 9b Copyright 2003, Cisco Systems, Inc. ... Lab 3 .1. 9b Fluke 620 Basic Cable Testing Objective • Use a simple cable tester to verify whether a straight-thru ... cables will be created. Simple Cable Testers: There are a number of basic cable testers a...
Ngày tải lên: 24/01/2014, 19:20
Tài liệu Lab 3.1.5 Configuring a Serial Interface pptx
... Router 1 GAD DCE 19 2 .16 8 .15 .1 255.255.255.0 class cisco Router 2 BHM DTE 19 2 .16 8 .15 .2 255.255.255.0 class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 5 Copyright ... __________________________________________________________________________ Step 10 Verify that the serial connection is functioning a. ping the serial interface of the oth...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.5 Series Circuits docx
... 1 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright 2003, Cisco Systems, Inc. Battery Lab 3 .1. 5 Series Circuits Switch Bulb ... LEDs with resistors • 6v lantern battery 2 - 3 CCNA 1: Networking Basics v 3.0 - Lab 3 .1. 5 Copyright 2003, Cisco Systems, Inc. Step 1 Measure the Resistances of all devices Measure the ... basic electrical circuit...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.6 Making Configuration Changes doc
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 6 Making Configuration Changes Objective • Configure some basic router ... password Enable/VTY/Console passwords Gadsden 17 2 .16 .0 .1 255.255.0.0 Cisco1 3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc....
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.6 Making Configuration Changes ppt
... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 6 Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 6 Making Configuration Changes Router ... Enable Secret password Enable/VTY/Console passwords GAD 19 2 .16 8 .14 .1 255.255.255.0 class cisco Objective • Configure some basic router settings. • Bring interfaces up and down. • Make ... HyperTerminal session...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.7 Troubleshooting a Serial Interface doc
... __________________________________________________________________________ Step 9 Verify that the serial connection is functioning by pinging the serial interface of the other router London#ping 19 2 .16 8 .15 .2 Paris#ping 19 2 .16 8 .15 .1 a. From London, ... the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the la...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface docx
... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 7 Copyright 2003, Cisco Systems, Inc. Lab 3 .1. 7 Configuring an Ethernet Interface ... on the type of router. GAD(config)#interface fastEthernet 0 GAD(config-if)#ip address 19 2 .16 8 .14 .1 255.255.255.0 GAD(config-if)#no shutdown GAD(config-if)#exit GAD (config)#exit Note: ... HyperTerminal session lab...
Ngày tải lên: 11/12/2013, 13:15
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface pptx
... Routing Basics v 3.0 - Lab 3 .1. 7 Copyright 2003, Cisco Systems, Inc. Step 2 Configure the fastEthernet 0 interface GAD(config)#interface fastEthernet 0 GAD(config-if)#ip address 19 2 .16 8 .14 .1 ... Router 1 GAD 19 2 .16 8 .14 .1 255.255.255.0 class cisco Objective • Configure an Ethernet interface on the router with an IP address and a subnet mask. Background/Pr...
Ngày tải lên: 11/12/2013, 13:15