Tài liệu Nghệ thuật xếp hình Nhật Bản:ratracer 2 docx
Tài liệu Nghệ thuật xếp hình Nhật Bản:dragonfly 2 docx
... right.
2
22. Flip 1 flap over, and pull
the next flap towards the left.
Model won’t lie flat.
22 -23
24 . Repeat 22 -23 on left.
Turn over.
25 . Fold top point to center.
Turn back over.
26 . Valley ... downwards.
Don’t crease.
20 . Reverse-fold, flipping over
the rectangular single-ply.
Press flat and sharpen all
creases.
16 -20
21 . Repeat 16 -20 on left.
Turn over.
not to
corne...
Tài liệu Nghệ thuật xếp hình Nhật Bản: humming bird docx
... Hummingbird - Collin Weber Page 2 of 4
Hummingbird - Collin Weber Page 4 of 4
Hummingbird - Collin Weber Page 3 of 4
Tài liệu Nghệ thuật xếp hình Nhật Bản:goldfish-ranchu docx
... convexes outwards.
26 . 27 . 28 .
29 .
30.
31.
32.
Now valley fold then unfold Steps 25 and 26 . Lift up the first layer
then fold in the left corner
along creases made in
Step 26 .
Fold the next ... assembly as shown.
20 . 21 . 22 .
Valley fold then crimp fold each
side.
Fold assembly in half while
lifting out the layer at the
top and a triangle at the
bottom
1/4
23 . 24...
Tài liệu Nghệ thuật xếp hình Nhật Bản: dragon fly docx
... right.
2
22. Flip 1 flap over, and pull
the next flap towards the left.
Model won’t lie flat.
22 -23
24 . Repeat 22 -23 on left.
Turn over.
25 . Fold top point to center.
Turn back over.
26 . Valley ... downwards.
Don’t crease.
20 . Reverse-fold, flipping over
the rectangular single-ply.
Press flat and sharpen all
creases.
16 -20
21 . Repeat 16 -20 on left.
Turn over.
not to
corne...
Tài liệu Nghệ thuật xếp hình Nhật Bản:battle cruiser_2 docx
... front.
20 . Finished from on top
21 . Finished from the side.
Klingon D-7 Battle Cruiser
By Perry Bailey Copyright 1997, and 20 00
1. Start with bill facing up fold in half,
crease and unfold.
2. Fold ... diagonls across the bill and a valley
fold between the two x’s.
4. Using the diamond formed
by the 2 big x,s swivel fold
out the end of the bill as you
fold it over.
5.Should look...
Tài liệu Nghệ thuật xếp hình Nhật Bản:Fluff All docx
... 22 .Swing over. 23 .Petal up. 24 .Swing up.
27 .Valley outwards .26 .Swing down .25 .Sink triangularly.
28 .Precrease flap halfway. 29 .Valley along precrease. 30.Valley ... base of
model.
32. Pull up the thick set of layers31.Swing over flap A, while
incorporating a reverse fold.
A gusset will form where flap
A meets the point.
Flap A
Edge B
22 -33
1 /2
36-37,39-40
3-5
34.Repeat ......
Tài liệu Nghệ thuật xếp hình Nhật Bản:jack_in_a_box_2 ppt
... 12.
13.
14.
❴✎❵✦❬★❛✪❜✫❭✭❝✮❭✭❞✰❝✱❩✌❡
❢✵❣✛❤★❤◆✐
✂✁☎✄✝✆✟✞✡✠☛✁✌☞✎✍✑✏✓✒✕✔✗✖✙✘✛✚✢✜✙✣
1/3
7.
1/ 12
6.
1.
2.
1/ 121 / 12
8.
1−4
4.
3.
5.
I. PRECREASES.
✤✎✥✦✘★✧✪✩✫✚✭✬✮✚✭✯✰✬✱✖✌✲
✳✵✴✛✶★✶
✜
✷✂✸☎✹✝✺✟✻✡✼☛✸✌✽✎✾✑✿✓❀✕❁✗❂✙❃✛❄❆❅❈❇
o
180
1/ 12
6. 7.
o
90
o
1.
90
o
90
o
90
o
2.
3.
5.4.
8. 9.
10.
II. ... ✿◆✻❖✽◗❘✷❚❙✌❅✲✺❋●✚❯✄✳✲●✭❅✡✯✲✱✴❙❲❱✩❇❚●❳■❋✳✲❂❲❍✌❊❋❅❆●✭❯✄✱
❨
❂✆❩✗❂✚❬❭✵✸✷❉❍❲✯✲✺❫❪❀✷❚❙✌❅✲✺✤❑
❴✭❵❜❛◗❝
✦✩❞
❝...
Từ khóa: