Tài liệu Nghệ thuật xếp hình Nhật Bản:flower 2 pdf

... Dragonfly (continued) Copyright 1998-99 Stephen Hecht. All Rights Reserved 22 -27 28 . Repeat 22 -27 on left. Turn over. 29 . Detail of top point. Fold and unfold tip down to base of triangle. 30. ... upper wing downwards. 20 . Reverse-fold, flipping the single-ply over. Sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. 3 22 . Flip 1 flap over, and pull the next 2...

Ngày tải lên: 10/12/2013, 12:15

... Actually I am told this is a D-7 Battle cruiser 20 .

Ngày tải lên: 10/12/2013, 12:15

Ngày tải lên: 21/12/2013, 02:20

Ngày tải lên: 21/12/2013, 03:15

... with 1 /2 of a square or 2: 1 ratio piece of paper, large paper is not needed as a 6X3 piece of foil works well. Fold the foil into sixteenths, with skin color desired on the out side. 2. reverse ... reverse fold in the first 2 corners on each side. 3. pull down the pleats to form the arms. 4. reverse fold down the top from the center fold to form the head. page 1 of 2 By Perry...

Ngày tải lên: 21/12/2013, 03:15

... © July 1999 2 3 4 5 6 7 Repeat steps 5 and 6 on the other 3 sides 8 9 Fold 2 layers to the left 10 11 Fold 1 layer to the right (front and back to even up the layers on each side) 12 Fold 1 layer ... back to even up the layers on each side) 12 Fold 1 layer to the top 180º 13 14 Valley fold the 2 small points. Note that the lower edges are slightly above the centre crease 15 16 Squas...

Ngày tải lên: 21/12/2013, 03:15

... corners. 21 . Kész a virág. Finished flower. 19. Váltóhajtás (csak egy réteget) a középponttól a harmadik hajtásélig. Reverse-fold one layer. The fold goes from the center to the third crease. 20 . A ... fülön. Divide into fourths on all four flaps. 11. Fordítsd meg a modellt! Turn the model over. 12. Tovább felezünk (nyolcadokra). Divide further into eights. 14. Oda-visszahajtjuk a többi...

Ngày tải lên: 17/01/2014, 04:20

... Repeat step 1-4 Mountain fold the points and unfold http://www.thok.dk/flexbox.html (1 of 2) [25 /07/ 02 06:39:06]

Ngày tải lên: 17/01/2014, 04:20

Ngày tải lên: 17/01/2014, 04:20

... right. 2 22. Flip 1 flap over, and pull the next flap towards the left. Model won’t lie flat. 22 -23 24 . Repeat 22 -23 on left. Turn over. 25 . Fold top point to center. Turn back over. 26 . Valley ... downwards. Don’t crease. 20 . Reverse-fold, flipping over the rectangular single-ply. Press flat and sharpen all creases. 16 -20 21 . Repeat 16 -20 on left. Turn over. not to corne...

Ngày tải lên: 17/01/2014, 04:20