Quản trị mạng Lab 4-5 - RIP & IGRP
Quản trị mạng Lab 4-5 - RIP & IGRP
... CCNA LAB No. 4-5 : CONFIGURE Static route – RIP – IGRP Lab time: 1 Task 2: RIP1 . Đặt địa chỉ cho router: (Ví dụ: router 3)Router> enable ... Router(config)#router rip : bật giao thức rip lên Router(config-router)#network network-number : gõ các mạng kết nối trực tiếp với routerVí dụ: với router R3:Router(config-router)#network ... 192.168.168.3 255.255....
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng LAB 1 - Basic config router
... copy running-config startup-config +Copy file startup-config from router to TFTP server at 192.168.1.253 Router#copy startup-config tftp Example: 10-Perform ... password for telnet Router (config-line)#password cisco +Allow login Router(config-line)#login 4- Configure password for accessing enable mode : 123456 ... A.Basic lab 1- Access router X through Access Server If there are...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng LAB 3 - LAN switching
... Switch_A(config)#line vty 0 4 Switch_A(config-line)#login Switch_A(config-line)#password <password > ;-5 . Configure Switch_A so that after telnet to Switch_A, ... passwords : Switch_A(config)#enable password <password > Switch_A(config)#enable secret <password > 6. Be sure that all passwords, which has been configured ... Switch_A(config)#interface f0/5 Switch_A(config-if...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng Lab 6 - OSPF & EIGRP
... defined with the ip summary-address eigrp command Router(config-if)#ip summary-address eigrpautonomous-system-number ip-address mask administrative-distance 8. The EIGRP hello interval should ... R1(config-if)#ip hello-interval eigrp 1000 109.To verify operation of EIGRP ,the commands should be issued : R1#show ip eigrp topology R1#sh ip eigrp neighbors ... CCNA LAB No. 6 : CONFIGURE OSPF...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng Lab 7 - InterVLAN
... Sw355 0-2 (config)#vlan 2 Sw355 0-2 (config)#int f0/2 Sw355 0-2 (config-if)#switchport mode access Sw355 0-2 (config-if)#switchport access ... Router. Sw355 0-2 (config)#int f0/4 Sw355 0-2 (config-if)#switchport trunk encapsulation dot1q Sw355 0-2 (config-if)#switchport mode trunk ... CCNA LAB No. 7: Inter VLAN Routing CONFIGURATION Lab time: 1 session Students are r...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng Lab 8 - NAT
... R-X(config-if)#ip nat inside R-X(config)#int e0 R-X(config-if)#ip nat outside3. Configure static NAT on R-X so that the private ... translated R-X(config)# access-list 1 permit 100.0.X.0 0.0.0.255 - Define a pool of global addresses to be allocated as needed R-X(config)#ip nat pool <name> 10.2.0.12X 10.2.0.13X ... R-X(config)#int e0 R-X(config-if)#ip address 10.2.0.16X 255.255.25...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng Lab 9-ACL
... access list RouterX(config)#ip http access-class <access-list>4. Use access-class to deny telnet sessions in routers ... with PCs in the lab. RouterX(config)#int e0 RouterX(config-if)#ip address 10.2.0.16X 255.255.255.0 RouterX(config-if)#no shut3. Be ... CCNA LAB No. 9: ACCESS LIST CONFIGURATION Lab time: 1 session Students are recommended to read the entire lab requireme...
Ngày tải lên: 13/11/2012, 10:56
Quản trị mạng Lab 10 - Frame relay
... learnedTask 3 :1. Delete hub-and-spoke configuration from task 2.2. Remain the same group as Task 23. Disable Inverse-ARP. Router(config-if)#no frame-relay inverse-arp 4. You decide ... Router3(config-if)#frame-relay map ip 192.168.100.2 302 broadcast Router3(config-if)#frame-relay map ip 192.168.100.1 301 broadcast Router2(config-if)#frame-relay ... point-to-pointĐối với các router multipoi...
Ngày tải lên: 13/11/2012, 10:56
