Tài liệu Configuring Frame Mode MPLS doc

... 2 frame before sending it across one of many supported Layer 2 media. At the next MPLS- enabled Label Switch Router (LSR), the MPLS frame is read and the IP packet is switched as an MPLS frame ... engineering. MPLS runs between Layers 2 and 3 of the OSI model and, because of this, is sometimes said to run at Layer 2½. The MPLS header is 4 bytes long and includes a 20-bit la...

Ngày tải lên: 13/12/2013, 11:15

... lab. Step 2 Configuring the serial interface a. In Frame Relay, the customer router is considered the DTE device. In order to configure the serial interface the Layer 2 Frame Relay frame type ... configure the frame type, use the following commands: Cork#configure terminal Cork(config)#interface serial 0 Cork(config-if)#encapsulation frame- relay IETF b. Next the forma...

Ngày tải lên: 18/01/2014, 05:20

... systemroot\system32\Shell32.dll . ✦ Console mode: Choose the mode in which you want the console to open for the next session. Choose between author mode and one of the three user modes discussed previously. ✦ ... chapter. The default mode in Windows 2000 is user mode limited access, single window. As mentioned earlier, you use author mode to author new consoles or modify existing o...

Ngày tải lên: 10/12/2013, 16:15

... broadcast frame- relay lmi-type ansi Remove the incorrect frame- relay map statement. Singapore(config-if)#no frame- relay map ip 192.168.192.2 17 broadcast Reenter the frame- relay map ... IP address via a “static” frame- relay map statement. “CISCO” identifies the Frame Relay encapsulation used with frame- relay map statement, which is the default Frame Relay encapsul...

Ngày tải lên: 11/12/2013, 14:15

... - 3 Semester 5: Advanced Routing v2.0 - Lab 6.7.1 Copyright  2001, Cisco Systems, Inc. 6.7.1 Configuring EIGRP with IGRP Fa0/0 192.168.232.1 /24 S0/1 192.168.240.1 /30 S0/0 192.168.224.2

Ngày tải lên: 11/12/2013, 15:15

... the bandwidth Interface Subconfiguration mode command. This command was discussed in Chapter 5. Configuring IP IGRP Setting up IGRP is almost as simple as configuring RIP: Router(config)# router ... process. First, you must go into Router Subconfiguration mode. This mode determines the routing protocol that you’ll be running. Within this mode, you’ll configure the characteristics of...

Ngày tải lên: 18/01/2014, 04:20

... restriction is that the paths must have the same cost. Configuring OSPF Configuring OSPF is slightly different from configuring RIP or IGRP. When configuring OSPF, use the following syntax: Router(config)# ... their neighbors, the multicast it via 224.0.0.5. Configuring OSPF requires you to specify a process ID, which is locally significant to the router. When configuring the netw...

Ngày tải lên: 18/01/2014, 04:20

... 5.2.2 Configuring Frame Relay PVC Objective • Configure two routers back-to-back as a Frame Relay permanent virtual circuit (PVC). This will be done manually, in the absence of a Frame Relay ... __________________________________________________________________________ Step 7 Showing Frame- Relay map a. To view the Layer 2 to Layer 3 mapping, use the show frame- relay map co...

Ngày tải lên: 18/01/2014, 05:20

... PVC. Step 8 Show the Frame Relay maps a. Look at the frame relay maps by typing the command show frame- relay map at the privileged exec mode prompt: Amsterdam#show frame- relay map b. ... 5.2.3 Configuring Frame- Relay Subinterfaces Objective • Configure three routers in a full-mesh Frame Relay network. An Adtran Atlas550 Frame Relay emulator is used to simulate...

Ngày tải lên: 18/01/2014, 05:20