Tài liệu LabVIEW Basics I Course Manual P2 pptx
Tài liệu LabVIEW Basics I Course Manual P2 pptx
... Developing Larger Projects in LabVIEW
LabVIEW Basics II Course Manual 5-2 ni.com
A. Assembling a LabVIEW Application
Lesson 1 of this course described a general approach to developing
LabVIEW applications. ... in LabVIEW
© National Instruments Corporation 5-9 LabVIEW Basics II Course Manual
Exercise 5-2 Application Exercise (5-2) VI
Objective: To add the Acquire Data V...
Tài liệu LabVIEW Basics I Course Manual P1 pptx
... new
elements.
2.
Right-click on
the border for a
new shift register.
1.
Initial Value 0
Initial Value 7
Initial Value 5
Initial Value 5
Run 1
Run 1
Run 2
Run 2
Uninitialized Shift Registers
Initialized Shift ... Iteration
Inital
Value
Inital
Value
New
Value
New
Value
Previous
Value
New
Value
Previous
Value
New
Value
Lesson 4 Loops and Charts
LabVIEW Basics I Course Manual 4-18 ni.co...
Tài liệu LabVIEW Basics II Course Manual ppt
... File I/ O Techniques
LabVIEW Basics II Course Manual 4-2 ni.com
A. Working with Byte Stream Files
LabVIEW s file I/ O functions make working with byte stream files, or text
and binary files, quite ... opening LabVIEW datalog
files.
File Dialog
Open File
© National Instruments Corporation 4-1 LabVIEW Basics II Course Manual
Lesson 4
Advanced File I/ O Techniques
When impl...
Tài liệu LabVIEW Basics I pptx
... during the course
and for doing certain course exercises
basics1 .llb
VI library containing subVIs used during the course
nidevsim.zip
Zip file containing the LabVIEW instrument driver
for the NI ... as
(Windows)
Notepad,
WordPad,
(Macintosh)
TeachText,
(UNIX)
Text Editor, vi, or vuepad
❑ LabVIEW Basics I course disks, containing the following files.
Filename Description
Disk...
Tài liệu Student Learning Guide Course Introduction P2 pdf
... accessories
• DVOM
• Identify circuit elements: power source,
load, protection device and ground
• Identify the different types of circuits
and circuit control methods
• Determine what is required ...
amperage and resistance in an
electrical circuit
• Current is directly proportional
to voltage and inversely
proportional to the resistance
in a circuit
• Published by George Simon
Ohm i...
Tài liệu Vận hành hệ thống điện P2 pptx
... nhiãưu ỉu i øm l giạ thnh i ûn nàng r, khäng tiãu hao nhiãn liãûu
Chè tiãu tä i ỉu ca sỉû phán bäú cän
i ûn v nhiãût i ûn l lm cỉûc tiãøu chi phê nhiãn liãûu åí nhiãût i ûn, âäưng thå i ... âån vë thå i gian åí nh m
3
ạy thy i ûn
thỉï i [ m /s ].
n1, =i voi),,(
,
TDiTDiii
Lỉåüng nỉåïc qui âënh âä i vå i thy i ûn thỉ
PPtQQ =
(2-36)
ưu tiã
Khi âọ bi tọan âỉåüc phạt biãøu nhỉ .....
Tài liệu Microsoft Access 2007 Data Analysis P2 pptx
... storing your data using this approach is eliminat-
ing or significantly decreasing duplicate information. Later in the chapter,
you will learn about the dangers inherent in storing data with ... makes it truly unique in the industry.
However, it is not without its limitations, as you will see in the following
section.
Where Data Analysis with Excel Can Go Wrong
Years of consulting experience...
Tài liệu Student Learning Guide Course Introduction P1 pptx
... Two
Video
Day TwoDay Two
Electrical Diagnosis
Day TwoDay Two
Electrical DiagnosisElectrical Diagnosis
1:45-2:45
Classroom/Shop Discussion/Activity
Electrical DiagnosisElectrical Diagnosis
2:45-3:00 ... indicates continuity
or a short circuit. An out of limits (OL) reading
indicates that there is an infinite amount of
resistance or an open in a circuit.
To measure continuity or resistan...
Tài liệu Asea Brown Boveri Pocket Book P2 pptx
... means. In outdoor installations,
therefore, aluminium/copper connectors or washers of copper-plated aluminium sheet
are used to join aluminium and copper, while in dry indoor installations aluminium ... temperature.
Index 1 refers to the radiating surface, Index 2 to the radiated surface.
C
12
is the effective radiation transfer coefficient. It is determined by the geometry and
emissivity
ε...
Tài liệu Giáo trình công nghệ Laser P2 pptx
... pháp i n x i mòn
( i n ăn mòn) [6]
Các giai đoạn xảy ra khi gia công :
a/ Giai đoạn tác dụng xung i n;
b/ Giai đoạn kim lo i bị bắn ra kh i bề mặt;
c/ Giai đoạn sau khi gia công. ...
các chùm tia có
nhiệt):
Plasma, i n tử,
tia
laser,
Phơng pháp i n x i
mòn (tia lửa i n, xun
g
i n, tiế
p xúc i n anốt
- cơ,
2.3 - Đặc i m của các phơng pháp gia công đặc biệt :
....
Từ khóa:
- tài liệu máy in laser toàn tập p2
- tài liệu công nghệ kéo sợi pp 4 pptx
- tài liệu tiêu chuẩn quốc tế iso 22000 pptx
- tài liệu bệnh án siêu âm tổng quát pptx
- tài liệu quy trình làm dự án cntt pptx
- tài liệu lịch sử lớp 7 bài 21 pptx
- tài liệu miếu bà chúa xứ núi sam pptx
- tài liệu hóa học môi trường chương iii pptx