Tài liệu Control Systems Simulation using Matlab and Simulink pptx

... Engineering ME134 Automatic Control Systems Spring 2002 Report Due: Tuesday, February 26 One report per group is required. Control Systems Simulation Using Matlab and Simulink 1 Introduction In ... system 6 “Hands-on” Design of Control Systems “Hands on Design systems refers to directly working with the system to be controlled and trying a variety of controllers and...

Ngày tải lên: 12/12/2013, 07:15

... amplitudes in bands less than ‘1X’ and ‘1X’ A1: the ratio of peak amplitudes in band ‘1X’ and its initial record (in good condition) A2: the ratio of peak amplitudes in bands ‘2X’ and ‘1X’ A3: ... consists of ten objects and can be described using two concepts, namely “d = 0” and “d = 1.” As already mentioned, two conflicts, namely objects x 5 and x 7 , and objects x 6 and x...

Ngày tải lên: 22/12/2013, 21:18

... modeling and simulations, soft computing, intelligent adaptive control systems, and optimization. He has also organized many short-term courses in the area of modeling and simulation of systems, and ... understanding of systems and their modeling and simulation Explain the step-by-step procedure for modeling using top-down, bottom-up, and • middle-out approaches D...

Ngày tải lên: 01/04/2014, 10:55

... 1.2 shows additional MATLAB commands to get one started on MATLAB. Detailed descriptions and usages of the commands can be obtained from the MATLAB help facility or from MATLAB manuals. Table ... 1.1 MATLAB BASIC OPERATIONS When MATLAB is invoked, the command window will display the prompt >>. MATLAB is then ready for entering data or executing commands. To quit...

Ngày tải lên: 22/12/2013, 19:17

Ngày tải lên: 23/12/2013, 03:16

... during the boot process. Using the DOS commands FDISK and FORMAT, the hard drive can be partitioned and prepared for communication and usage. Step 1 Boot up the computer using a bootable floppy ... bootable floppy disk with the FDISK and FORMAT commands on it. Step 2 To create and remove partitions, first start the FDISK program. Type “FDISK” at the prompt and then pres...

Ngày tải lên: 18/01/2014, 05:20

... amplifier is at 200 Hz and the gain is - 500. The pole of the voltage amplifier and level shifter is 400 KHz and has a gain of 360. The pole of the output stage is 800KHz and the gain is 0.92. ... Solution Using voltage division V V s sC RsC IN 11 11 1 1 () = + (11.26) From Equation (11.24) V V s R sC O 1 2 2 1 1 () =+ (11.27) Using Equations (11.26 ) and...

Ngày tải lên: 19/01/2014, 17:20

... the conduction band E V = energy in the valence band and k, T, m n * and m p * were defined in Section 10.1. In an intrinsic semiconductor (Si and Ge) m n * and m p * are ... direct band gap semiconductor. The energy levels of the outer electrons form energy bands. In insulators, the lower energy band (valence band) is completely filled and the next energy b...

Ngày tải lên: 19/01/2014, 17:20

... approaches for solving I D and V D . In one approach, Equations (9.10) and (9.11) are plotted and the intersection of the linear curve of Equation (9.10) and the nonlinear curve of Equation ... 10V, and the reverse saturation current of the diode is 10 -12 A and n = 2.0. (Assume a temperature of 25 o C.) (a) Use MATLAB to plot the diode forward characteristic c...

Ngày tải lên: 19/01/2014, 17:20

... coeffi- cients a n and b n . (b) Write a MATLAB program to obtain a n and b n for n = 0 , 1, , 10 by using Equations (8.5) and (8.6). (c) Resynthesis g(t) using 10 terms of ... 8.1. If gt () is continuous and non- periodic, then Gf () will be continuous and periodic. However, if g(t) is continuous and periodic, then Gf () will discrete and non...

Ngày tải lên: 19/01/2014, 17:20