Tài liệu Debug isdn q931 Command Call Setup Procedure Field Descriptions doc
... debug isdn q931 Command Call Setup Procedure Field Descriptions Field Description TX -> Indicates that this message is being ... set Calling Party Number Identifies the origin of the call; this field is present only in incoming SETUP messages; this field uses the IA5 character set CALL_ PROC Indicates the CALL PROCEEDING ... Q.931 Called Party...
Ngày tải lên: 11/12/2013, 14:15
... indicates it is a call- control procedure; note that the Layer 2 management procedures such as TEI assignment, TEI removal, and TEI checking, which are tracked with the debug isdn q921 command, do ... currently, this field can have the value 0 (for call- control procedure) or 63 (for Layer 2 management procedures) tei Indicates the TEI that has been assigned automatically b...
Ngày tải lên: 11/12/2013, 14:15
... Network Connections control netconnections Network Connections ncpa.cpl Network Setup Wizard netsetup.cpl Notepad notepad Nview Desktop Manager (If Installed) nvtuicpl.cpl Object ... certmgr.msc Character Map charmap Check Disk Utility chkdsk Clipboard Viewer clipbrd Command Prompt cmd Component Services dcomcnfg Computer Management compmgmt.ms...
Ngày tải lên: 09/12/2013, 22:15
Tài liệu Beginning the Linux Command Line [Apress 2009] ppt
... the source code of the command. /PTIONS ARE VERY SPECIFIC TO THE COMMAND YOU USE 3OME COMMANDS DONT HAVE ANY OPTIONS and other commands can have more than 50. The i]j command normally gives ... WITH THESE line commands as easy as possible. 3OME SHELLS OFFER THE OPTION TO COMPLETE A COMMAND AUTOMATICALLY "ASH HAS THIS FEATURE BUT IT DOES MORE THAN JUST COMPLETE COMMANDS &quo...
Ngày tải lên: 10/12/2013, 14:15
Tài liệu Debug Options docx
... timestamps debug uptime command back into the configuration. Step 4 The terminal monitor command. Debug output does not display to the screen if you are in a telnet session. To see the debug ... Gateway: 192.168.1.1 Default Gateway: 192.168.2.1 Step 2 The debug ip packet command. This command while a heavy user of CPU resources, documents the IP traffic activity on the ro...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu show tech-support Command docx
... HyperTerminal and designate a document called ShowTech-Support.TXT on either a floppy disk or the computer’s desktop. Once it is started, rerun the show tech-support command. When it is done be ... show tech-support Command SanJose1 SanJose2 #2#1 S0/0 S0/0 192.168.1.10 192.168.2.10 Objective This lab you will look at the output of one command the show tech- support command that...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Show frame-relay pvc Command Field Descriptions doc
... Show frame-relay pvc Command Field Descriptions Field Description DLCI One of the DLCI numbers for the PVC DLCI USAGE Lists SWITCHED ... voice traffic Voice Reserved Queues Queue numbers reserved for voice traffic on this PVC; this field was removed in Cisco IOS Release 12.0(5)T Fragment Type Type of fragmentation configured
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Remote ISDN Site not Answering doc
... attempting an ISDN session with PPP specific debugging turned on. SanJose3#undebug all All possible debugging has been turned off SanJose3 #debug ppp authentication PPP authentication debugging ... SanJose3 #debug ppp negotiation PPP protocol negotiation debugging is on London#undebug all All possible debugging has been turned off London #debug ppp authentication PPP authent...
Ngày tải lên: 11/12/2013, 14:15
Tài liệu Cisco Security Appliance Command Line pdf
... EXEC Mode (the enable Command) 6 43 Cisco Security Appliance Command Line Configuration Guide OL-12172-01 About This Guide Document Conventions Document Conventions Command descriptions use these ... specifications. Table 1 Document Organization (continued) Chapter/Appendix Definition 40 Cisco Security Appliance Command Line Configuration Guide OL-12172-01 About This Guide Rel...
Ngày tải lên: 21/12/2013, 05:18
Tài liệu show ipx traffic Command Field Descriptions pptx
... improperly configured. show ipx traffic Command Field Descriptions Field Description Time since last clear Elapsed time since last clear command issued. Rcvd: Description of the packets ... requests, and replies. This field applies to Cisco IOS Release 11.2 and later. SAP Get Nearest Server, requests, replies Number of GNS requests and replies. This field applie...
Ngày tải lên: 21/12/2013, 19:15