Tài liệu show interfaces bri Field Descriptions doc

... show interfaces bri Field Descriptions Field Description BRI Is {up | down | administratively down} Indicates whether the ... long; when the number of hours in any of the "last" fields exceeds 24 hours, the number of days and hours is printed; if that field overflows, asterisks (**) are printed Output Queue, ... transmitter has been running faster than the...

Ngày tải lên: 11/12/2013, 14:15

... debug isdn q921 Field Descriptions Field Description Jan 3 14:49:47.391 Indicates the date and time at which the frame ... during the TEI check procedure; this message is sent in a UI command frame; the ri field is always 0; the ai field for this message contains either a specific TEI value for the local router to ... in a UI command frame in response to the IDCKRQ message;...

Ngày tải lên: 11/12/2013, 14:15

... 5 Activate the BRI connection Activate the ISDN BRI using the no shutdown command at the interface configuration prompt. Ottawa#configure terminal Ottawa(config)#interface bri 0 Ottawa(config-if)#no ... using the IOS keyword basic-ni. To check the ISDN BRI status, issue the following command before issuing any configuration commands: Ottawa #show isdn status b. What is...

Ngày tải lên: 21/12/2013, 19:15

... Show frame-relay pvc Command Field Descriptions Field Description DLCI One of the DLCI numbers for the PVC DLCI USAGE ... voice traffic Voice Reserved Queues Queue numbers reserved for voice traffic on this PVC; this field was removed in Cisco IOS Release 12.0(5)T Fragment Type Type of fragmentation configured

Ngày tải lên: 11/12/2013, 14:15

... debug isdn q931 Command Call Setup Procedure Field Descriptions Field Description TX -> Indicates that this message is being transmitted from the ... Number Identifies the called party; this field is present only in outgoing SETUP messages; note that it can be replaced by the Keypad Facility field; this field uses the IA5 character set Calling ... identifier; the val...

Ngày tải lên: 11/12/2013, 14:15

... show ipx interface e0 Command Field Descriptions Field Description Ethernet0 is up, line protocol is up Type of interface ... encapsulation being used on the interface, if any Delay of this IPX network, in ticks Value of the Ticks field (configured with the ipx delay command) Throughput Throughput of the interface (configured

Ngày tải lên: 21/12/2013, 19:15

... show ipx traffic Command Field Descriptions Field Description Time since last clear Elapsed time since last clear ... requests, and replies. This field applies to Cisco IOS Release 11.2 and later. SAP Get Nearest Server, requests, replies Number of GNS requests and replies. This field applies to Cisco IOS ... SAP Nearest Name requests, replies Number of SAP Near...

Ngày tải lên: 21/12/2013, 19:15

... X Magnetic Field §1. Magnetic interaction and magnetic field §2. Magnetic forces on a moving charged particle and on a current-carrying conductor §3. Magnetic field of a current – magnetic field calculations §4. ... current loop:  Consider loop in magnetic field as on right: If field is to plane of loop, the net force on loop is 0! • If plane of loop is not to field, there wil...

Ngày tải lên: 10/12/2013, 12:15

... interface state change interrupt 4 2704 2360/3000 Network interfaces 5 124296 2868/3000 Console Uart show interfaces (Basic show interfaces command from CCNA days) 7-12 Semester 8 ... Consider reviewing this with your text for reference. Many of the fields are explained. SanJose1# SanJose1 #show tech-support show version (Displays the systems hardware a...

Ngày tải lên: 11/12/2013, 14:15

... Show Pablo & Bruno 1 • Tôi đến đây để chia sẻ với bạn một cơ hội thương mại đã mở cửa ở Việt

Ngày tải lên: 22/12/2013, 07:17