Tài liệu Lab 7 2 4 Selecting the Root Bridge docx

... the Basic Switch Configuration lab. 1 - 5 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2. 4 Copyright  20 03, Cisco Systems, Inc. Step 2 Configure the hosts attached to the ... determined that the switch selected as the root bridge, by using default values, is not the best choice. It is necessary to force the “other” switch to become the r...

Ngày tải lên: 11/12/2013, 14:15

... CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2. 4 Copyright  20 03, Cisco Systems, Inc. Lab 7. 2. 4 Selecting the Root Bridge Objective • Create a basic switch configuration ... as the root switch with the factory default settings. • Force the other switch to be selected as the root switch. Background/Preparation Cable a network...

Ngày tải lên: 05/11/2013, 12:15

... 800, 1600, 170 0, 25 00, 26 00 routers, or a combination, may be used. Please refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment ... 3.0 - Lab 7. 2. 6 Copyright  20 03, Cisco Systems, Inc. c. If the answer is no for either question, troubleshoot the router configurations using show ip route to...

Ngày tải lên: 11/12/2013, 14:15

... the Basic Switch Configuration lab. 2 - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2. 6 Copyright  20 03, Cisco Systems, Inc. Step 2 Configure the hosts attached to the ... Record the states of the first 12 interfaces and ports of each switch. Switch A Port # Switch B 1 2 3 4 5 6 7 8 9 10 11 3 - 4 CCNA 3: Switching Basics and Intermed...

Ngày tải lên: 11/12/2013, 14:15

... password Enable/VTY/Console passwords Router 1 GAD 1 72 .16.0.1 DCE 1 72 . 17. 0.1 25 5 .25 5.0.0 class cisco Router 2 BHM 1 72 .18.0.1 DTE 1 72 . 17. 0 .2 255 .25 5.0.0 class cisco Objective • Set up an IP ... this lab assignment before continuing. Step 1 Configure the routers 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7. 2. 6 Copyright  20 03, Cisco Sys...

Ngày tải lên: 11/12/2013, 14:15

... sending v1 update to 25 5 .25 5 .25 5 .25 5 via Serial0 (1 92. 168.15.1) *Mar 1 03: 12: 17. 555: RIP: build update entries *Mar 1 03: 12: 17. 555: network 1 92. 168. 14. 0 metric 1 *Mar 1 03: 12: 22. 671 : RIP: received ... update from 1 92. 168.15 .2 on Serial0 *Mar 1 03: 12: 22. 671 : 1 92. 168.16.0 in 1 hops 3 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7. 2 .7 C...

Ngày tải lên: 11/12/2013, 14:15

... with the with the ping 1 92. 168.16 .2 – n 30 command on the host. As the pings are responded to the router generates IP packet information. Stop the debug by using the command undebug all on the ... this lab assignment before continuing. 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7. 2. 9 Copyright  20 03, Cisco Systems, Inc. Step 1 Configure the hos...

Ngày tải lên: 11/12/2013, 14:15

... mask all addresses Router 1 BHM 1 92. 168. 14. 1 DCE 1 92. 168.15.1 DCE 1 92. 168.13.1 25 5 .25 5 .25 5.0 Router 2 GAD 1 92. 168.16.1 DTE 1 92. 168.15 .2 DTE 1 92. 168.13 .2 255 .25 5 .25 5.0 Objective • Configure Load ... class cisco RIP 1 92. 168. 14. 0 1 92. 168.15.0 1 92. 168.13.0 Router 2 BHM class cisco RIP 1 92. 168.15.0 1 92. 168.16.0 1 92. 168.13.0 Router designati...

Ngày tải lên: 11/12/2013, 14:15

... 170 0, 25 00 and 26 00 or any such combination can be used. Please refer to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the ... gateway Step 7 Verify that the internetwork is functioning by pinging the FastEthernet interface of the other router a. From the host attached to GAD, ping the ot...

Ngày tải lên: 21/12/2013, 19:15

... to the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1 72 1 ... From the host attached to GAD, ping the other host attached to the BHM router. Was the ping successful? ___________ b. From the host attached to BHM, ping the o...

Ngày tải lên: 21/12/2013, 19:15