Tài liệu Lab 4 2 2 Establishing and Verifying a Telnet Connection pdf

... Lab 4. 2. 2 Establishing and Verifying a Telnet Connection Objective • Establish a Telnet connection to a remote router. • Verify that the application layer between source and destination ... information that was generated by the remote access router. Interface Is there a Carrier Detect signal Are the keepalive messages being received? 2 - 5 C...

Ngày tải lên: 11/12/2013, 14:15

... CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2 2 Copyright  20 03, Cisco Systems, Inc. Lab 4. 2. 2 Establishing and Verifying a Telnet Connection Objective • Establish a Telnet connection ... 1 92. 168.15.1 25 5 .25 5 .25 5.0 RIP class Cisco Router 2 BHM 1 92. 168.16.1 DTE 1 92. 168.15 .2 255 .25 5 .25 5.0 RIP class Cisco 2 - 5 CCNA 2: R...

Ngày tải lên: 11/12/2013, 14:15

... CCNA 4: WAN Technologies v 3.0 - Lab 4. 3 .2 Copyright  20 03, Cisco Systems, Inc. Lab 4. 3 .2 Configuring Legacy DDR Objective • Configure an ISDN router to make a Legacy dial-on-demand ... Background/Preparation In this lab, 2 ISDN routers are required. If ISDN routers are not available, review the lab to become familiar with the process. An Adtran Atlas550 ISDN...

Ngày tải lên: 18/01/2014, 04:20

... erase and reload instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2. 3 ... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2. 3 Copyright  20 03, Cisco Systems, Inc. Lab 4. 2. 3 Suspending and Disconnecting Telnet Sessions Ob...

Ngày tải lên: 11/12/2013, 14:15

... 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2 3 Copyright  20 03, Cisco Systems, Inc. Lab 4. 2. 3 Suspending and Disconnecting Telnet Sessions Objective • Establish a Telnet ... 25 5 .25 5 .25 5.0 RIP class cisco Router 2 BHM 1 92. 168.16.1 DTE 1 92. 168.15 .2 255 .25 5 .25 5.0 RIP class cisco 2 - 4 CCNA 2: Routers and Routing Basics...

Ngày tải lên: 11/12/2013, 14:15

... - 4 CCNA 1: Networking Basics v 3.0 - Lab 4. 2. 9e Copyright  20 03, Cisco Systems, Inc. Lab 4. 2. 9e Fluke LinkRunner – Cable and NIC Tests Objective • Become familiar with the capabilities ... straight-through patch cables, which are good and bad • Ethernet crossover cables • Ethernet cable from wall plate RJ -45 jack through a patch panel • Hub and/ or switc...

Ngày tải lên: 18/01/2014, 04:20

... - 4 CCNA 1: Networking Basics v 3.0 - Lab 4. 2. 9e Copyright  20 03, Cisco Systems, Inc. Lab 4. 2. 9e Fluke LinkRunner – Cable and NIC Tests Objective • Become familiar with the capabilities ... straight-through patch cables, which are good and bad • Ethernet crossover cables • Ethernet cable from wall plate RJ -45 jack through a patch panel • Hub and/ or switc...

Ngày tải lên: 18/01/2014, 04:20

... successful connection to a local ISDN switch. Background/Preparation This lab assumes that a router with an ISDN BRI U interface is available. An Adtran Atlas550 ISDN emulator is used to simulate ... cloud. If an ISDN router is not available, review the lab and perform as many, non-interface commands as possible. Cable a network similar to the one in the diagram above. Any r...

Ngày tải lên: 11/12/2013, 14:15

... 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2 .4 Copyright  20 03, Cisco Systems, Inc. Lab 4. 2 .4 Advanced Telnet Operations Objective • Use the telnet command to remotely access ... the chart at the end of the lab to correctly identify the interface identifiers to be 2 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2 .4 Copyright  2...

Ngày tải lên: 11/12/2013, 14:15

... CCNA 2: Routers and Routing Basics v 3.0 - Lab 4. 2 4 Copyright  20 03, Cisco Systems, Inc. Lab 4. 2 .4 Advanced Telnet Operations Objective • Use the telnet command to remotely access ... 2 BHM 1 92. 168.16.1 DTE 1 92. 168.15 .2 DCE 1 92. 168.13.1 25 5 .25 5 .25 5.0 Router 3 PHX 1 92. 168.17.1 NA No address DTE 1 92. 168.13 .2 255 .25 5 .25 5.0 2...

Ngày tải lên: 11/12/2013, 14:15