Tài liệu Lab 1 1 7 Using ping and tracert from a Workstation ppt
Tài liệu Lab 1.1.7 Using ping and tracert from a Workstation ppt
... 1 - 5 CCNA 1: Networking Basics v 3.0 - Lab 1. 1 .7 Copyright 2003, Cisco Systems, Inc.
Lab 1. 1 .7 Using ping and tracert from a Workstation
Objective
• Learn to use the TCP/IP Packet ... Groper (ping) command from a workstation.
• Learn to use the Trace Route (tracert) command from a workstation.
• Observe name resolution occurrences using W...
Tài liệu Lab 1.1.7 Using ping and tracert from a Workstation pdf
...
1 - 6 CCNA 1: Networking Basics v 3.0 - Lab 1. 1 .7 Copyright 2003, Cisco Systems, Inc.
Lab 1. 1 .7 Using ping and tracert from a Workstation
Objective
• Learn to use the TCP/IP Packet ... Groper (ping) command from a workstation.
• Learn to use the Trace Route (tracert) command from a workstation.
• Observe name resolution occurrences using...
Tài liệu Lab 3.1.7 Troubleshooting a Serial Interface doc
... Ethernet 1 (E1)
16 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial ... router and gateway router, and a default route between the gateway router and remote
router.
Cable a network similar to the one in the diagram above. Any router...
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface docx
... Serial 1 (S1)
17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
2600 FastEthernet 0/0
(FA0/0)
FastEthernet ... interface on the router with an IP address and a subnet mask.
Background/Preparation
In this lab the Cisco Discovery Protocol (CDP) commands will be used. CDP discovers...
Tài liệu Lab 3.1.7 Configuring an Ethernet Interface pptx
... FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
2600 FastEthernet 0/0
(FA0/0)
FastEthernet 0 /1 (FA0 /1) Serial 0/0 (S0/0) Serial 0 /1 ...
Interface #1
Serial
Interface #2
Interface
#5
800 (806) Ethernet 0 (E0) Ethernet 1 (E1)
16 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
17 00...
Tài liệu Lab 4.1.6 Using CDP Commands ppt
...
Address
Ethernet 0
Address
Subnet mask
(all interfaces)
Router 1 GAD DCE 56000 19 2 .16 8 .15 .1 192 .16 8 .14 .1 255.255.255.0
Router 2 BHM DTE Not set 19 2 .16 8 .15 .2 19 2 .16 8 .16 .1 255.255.255.0
... 2: Routers and Routing Basics v 3.0 - Lab 4 .1. 6 Copyright 2003, Cisco Systems, Inc.
Lab 4 .1. 6 Using CDP Commands
Objective
• Use CDP commands to...
Tài liệu Lab 2.1. Ngăn chặn dùng phần mềm trên Windows 7 pptx
... Thanh Quan, Q3, TP. HCM
Tel: 3.9322 .73 5 – 0 913 .73 5.906 Fax: 3.9322 .73 4 www.nhatnghe.com
Trang 7 /18
- Kết quả
2. Cấu hình ApplicationLocker
- Start Æ khung Search programs and ... TẠO C A MICROSOFT TẠI VIỆT NAM
10 5 Bà Huyện Thanh Quan, Q3, TP. HCM
Tel: 3.9322 .73 5 – 0 913 .73 5.906 Fax: 3.9322 .73 4 www.nhatnghe.com
Trang 16 /18
- Click phải Addit...
Tài liệu Lab 3.1. Cài đặt Windows 7 tự động qua mạng ppt
... VIỆT NAM
10 5 Bà Huyện Thanh Quan, Q3, TP. HCM
Tel: 3.9322 .73 5 – 0 913 .73 5.906 Fax: 3.9322 .73 4 www.nhatnghe.com
Trang 14 /42
- Chọn tham số DisplayName Æ Nhập giá trị NhatNghe
- Chọn tham ... C A MICROSOFT TẠI VIỆT NAM
10 5 Bà Huyện Thanh Quan, Q3, TP. HCM
Tel: 3.9322 .73 5 – 0 913 .73 5.906 Fax: 3.9322 .73 4 www.nhatnghe.com
Trang 16 /42
- Chọn tham số Filename...
Tài liệu Lab 3.1.4 Using Router show Commands pdf
...
Background/Preparation
This lab helps the student become familiar with the router show commands. The show commands
are the most important information-gathering commands available for the router. ... Display the time and date for the router
a. Enter the show clock command. What information is displayed? ______________________
Step 6 Display a cached list of host names and addresse...
Tài liệu Lab 3.1.4 Using Router show Commands ppt
... CCNA 2: Routers and Routing Basics v 3.0 - Lab 3 .1. 4 Copyright 2003, Cisco Systems, Inc.
Step 5 Display the router’s time and date
a. Enter the show clock command. What information is displayed? ...
specifically instructed otherwise.
Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab.
Note: Do not erase and reload the router prior...