Tài liệu Fravo Cisco 642-821 3 0 ppt

... interface-dlci 200 frame-relay class cisco ! interface Serial0 /0 . 30 0 point-to-point ip address 10. 1 .3. 1 255.255.255 .0 frame-relay interface-dlci 30 0 ! ! map-class frame-relay cisco ... http://www .fravo. com 34 642-821 http://www .fravo. com 32 http://www .cisco. com/en/US/about/ac1 23/ ac147/ac174/ac 202 /about _cisco_ ipj_arch ive_article09186a...

Ngày tải lên: 10/12/2013, 16:15

... Building Cisco Multilayer Switched Networks (Ciscopress) page 219 + 2 20 http://www .cisco. com/en/US/products/hw/routers/ps368/products_configuration_guide_chapter09 186a 008 007 c87c.html# 102 0417 ... http://www .cisco. com/en/US/products/sw/iosswrel/ps1 831 /products_configuration_guide_chapter0 9186a 008 007 ff07.html# 100 0946 Q48. Which statement describes Dynamic Trunkin...

Ngày tải lên: 10/12/2013, 16:15

... Category 3, 4,5 UTP 2 100 m 100 BaseT4 EIA/TIA Category 3, 4,5 UTP 4 100 m 100 BaseFX Multimode fiber (MMF) with 62.5 micron core; 1 30 0 nm laser 1 400 m (half-duplex) 2 ,00 0 m (full-duplex) Single-mode ... reboots. 6 40- 604 Switching 3. 0 www.testking.com - 7 - 10. Multicasts 10. 1 Unicast Traffic 10. 2 Broadcast Traffic 10 .3 Multicast Traffic...

Ngày tải lên: 10/12/2013, 17:15

... A. 10. 10. 10. 0/27 and 134 . 10. 15 .0/ 28 B. 10. 0 .0. 0/8 and 134 . 10. 10. 0/24 C. 134 . 10. 15 .0/ 28 and 192.75 .0. 0/22 D. All three. 35 0- 001 http://www .fravo. com 20 i interface serial 0 ip ... ipx routing 100 0. 100 0. 100 0 i interface Ethernet 0 IPX network ACA1 234 i interface Serial 0 encapsulation frame-relay ipx network 100 frame-rela...

Ngày tải lên: 21/12/2013, 05:17

... Q 135 . What is the decimal equivalent of 101 01 100 01 100 000 00 0 100 11 100 001 01? A. 172.96.19. 133 B. 192.96.19. 133 C. 172.96.19. 132 D. 172.96.18. 133 E. 172.192.19. 133 Answer: A 35 0- 018 ... match address 101 set trans bar access-list 101 permit ip 20. 1.1 .0 0 .0. 0.255 30 .1.1 .0 0 .0. 0.255 access-list 101 permit ip 20. 1.1 .0 0 .0. 0.255 40. 1.1 .0 0...

Ngày tải lên: 17/01/2014, 08:20

... complete the pattern Task 13: Finish the part. • Create a 0. 0 20 round at the base of the gear tooth • Pattern the round • Create a coaxial hole with a diameter of 2 .00 0 • Use Layers to hide ... of 6 .00 0 to represent the pitch diameter of the gear • The result is shown below Task 4: Create a datum point. • Set the selection filter to Datums, pick the involute curve and the 6 ....

Ngày tải lên: 20/01/2014, 04:20

... printers. SSH SwitchX RouterX Main Router ISP Remote Class Fa0/1 Con 0 Con 0 Fa0/12 Fa0 /0 Fa0/1 Fa0/11 S0 /0/ 0 192.168.1 .0/ 24 172 .31 .241.254 VPN TFTP Fa0/2 6 Chapter 1: Building a Simple Network These are ... minutes in a year – downtime] / [Number of minutes in a year]) * 100 = Percentage availability ([525 600 – 15] / [525 600 ]) * 100 = 99.9971 ■ Scalability: Scalability indica...

Ngày tải lên: 13/12/2013, 05:15

... Cisco SDM 30 9 Cisco SDM Overview 30 9 Configuring Your Router to Support Cisco SDM 31 1 Start Cisco SDM 31 2 More Link 31 4 Configuration Overview 31 4 Cisco SDM Wizards 31 6 Summary of Using the Cisco ... Security 30 5 Physical and Environmental Threats 30 6 Configuring Password Security 30 6 Configuring the Login Banner 30 7 Telnet and SSH Access 30 7 Summary of Und...

Ngày tải lên: 13/12/2013, 05:15

... Features 100 Cisco VPN 30 05 Concentrator 101 Cisco VPN 30 15 Concentrator 102 Cisco VPN 30 30 Concentrator 1 03 Cisco VPN 30 60 Concentrator 104 Cisco VPN 30 80 Concentrator 104 Cisco VPN 30 00 Concentrator ... LED Indicators 105 Cisco Secure VPN Client Features 108 Cisco VPN 30 02 Hardware Client 108 Cisco VPN Client 109 Table of Cisco VPN 30 00 Concentr...

Ngày tải lên: 13/12/2013, 05:15

... : 01 67 6789 668 Email : newdark2 702 @yahoo.com.vn 3ds.group@gmail.com Web : http://vn.myblog.yahoo.com/kts-thanh TP. HCM, ngày 03 / 10/ 200 8 id1 508 187 pdfMachine by Broadgun Software ... và trên grid. 10. BÀI TẬP THỰC HÀNH: Vẽ một cái ghế có kích thước như sau: 40cm d=4cm 40cm cao 7cm d = 40cm Ø = 40cm Training and expressing 3Ds max – Sk...

Ngày tải lên: 13/12/2013, 22:15