Tài liệu ADC KRONE - Guide - Fiber in Broacast & Production Facility - 10 thing should know docx

... Terminations 8 7. Splicing vs. Field Connectors 9 8. Slack Storage 10 9. Fiber Density 11 10. Planning for Future Growth 12 Fiber for Broadcast and Entertainment Professionals Top Ten Things to Know Top ... include: • Bend radius: At turns in fiber runs, maintain a 1.5-inch bend radius. Tighter bends may cause micro-bending of individual fibers that allow light to escape the sign...

Ngày tải lên: 10/12/2013, 03:15

... Terminations 8 7. Splicing vs. Field Connectors 9 8. Slack Storage 10 9. Fiber Density 11 10. Planning for Future Growth 12 Fiber for Broadcast and Entertainment Professionals Top Ten Things to Know Top ... include: • Bend radius: At turns in fiber runs, maintain a 1.5-inch bend radius. Tighter bends may cause micro-bending of individual fibers that allow light to escape the sign...

Ngày tải lên: 24/01/2014, 03:20

... Terminations 8 7. Splicing vs. Field Connectors 9 8. Slack Storage 10 9. Fiber Density 11 10. Planning for Future Growth 12 Fiber for Broadcast and Entertainment Professionals Top Ten Things to Know Top ... include: • Bend radius: At turns in fiber runs, maintain a 1.5-inch bend radius. Tighter bends may cause micro-bending of individual fibers that allow light to escape the sign...

Ngày tải lên: 10/12/2013, 02:15

... 802.3z 100 0BASE-SX Gigabit Link @ 1310nm Laser IEEE 802.3z 100 0BASE-LX 10 Gigabit Link @ 850nm Laser IEEE 802.3ae 10GBASE-SR 10 Gigabit Link @ 1 310 CWDM Laser IEEE 802.3ae 10GBASE-LX4* 62.5/125 ... now 10 Gigabit. The rapid growth of Internet use and bandwidth-intensive applications combined with routine transmission of large files is driving the need for 10 Gigabit Ether...

Ngày tải lên: 10/12/2013, 02:15

... & Tail Cords. Inter-building Campus Cabling Use LSPM 2 x wavelengths, both in 2 x directions, AND ALSO Use OTDR For Links less than 300m, It is not an ADC KRONE requirement. For Links ... Pacific) OF Testing ADC KRONE Requirements V7_1&3T Dr2Page 10 of 12 27 OTDR Testing, Unacceptable Results Due To Ghosting “Ghosting” is the persence of multiple peaks in...

Ngày tải lên: 10/12/2013, 02:15

... optical fiber) . We can find z by using the law of sines: c=z C=2α A=9 0- α+θ ( ) b = y + 2tan α x 0 c = sin(A) bsin(C) cos α 1 2 cos α 1 (Using the imaginary lines in Figure 4 to find the ... the pistoning of the fiber within the ferrule. But if we reduce the minimum fiber height requirement, we can easily increase the apex offset a small amount and maintain physical contact i...

Ngày tải lên: 10/12/2013, 02:15

... 24 -fiber, 72 -fiber , 96 -fiber and 144 -fiber cables. Trying to match these cables up to splice panels based on a 144 -fiber capacity can be difficult and generally involves splitting the sub-units ... the termination panels used in the ODF. In large fiber count applications, with more than 432 incoming OSP fibers, splicing in a remote location can increase the termination densi...

Ngày tải lên: 10/12/2013, 02:15

... 10GBE Alien CrossTalk Mitigation 060625 Mitigation Techniques To Reduce Alien Crosstalk Noise In 10GBE Channels Using UTP Cabling These mitigation techniques are good installation ... carry 10GBE applications by applying where possible a combination of some of the following; At the Floor Distributor Remove cable ties from bundles in the telecommunication room racks, cabinets ... coupling...

Ngày tải lên: 20/12/2013, 22:15