Tài liệu ADC KRONE - Guide - 10GBase-T - Mitigation technique to reduce Alien CrossTalk docx

... 10GBE Alien CrossTalk Mitigation 060625 Mitigation Techniques To Reduce Alien Crosstalk Noise In 10GBE Channels Using UTP Cabling These mitigation techniques are good installation ... and/or patch cord separation. Change from a cross-connect to an interconnect cabling arrangement. The unused cross-connect panels or modules are re-usable for other circuits or other location...

Ngày tải lên: 10/12/2013, 02:15

... 672 STS3 (STM-1) 155.520 2016 STS-1OC-1 51.840 627 (STM-1) STS-3/OC-3 155.520 2016 (STM-4) STS-12/OC-12 622.080 8064 FIBER OPTIC CABLE (STM-16) STS-48/OC-48 2488.320 32,256 STS-192/OC-192 9953.280 ... 2004 ADC Telecommunications, Inc. All Rights Reserved Web Site: www .adc. com From North America, Call Toll Free: 1-8 0 0-3 6 6-3 891 • Outside of North America: + 1-9 5 2-9 3 8-8...

Ngày tải lên: 10/12/2013, 02:15

... 10GBE Alien CrossTalk Mitigation 060625 Mitigation Techniques To Reduce Alien Crosstalk Noise In 10GBE Channels Using UTP Cabling These mitigation techniques are good installation ... and/or patch cord separation. Change from a cross-connect to an interconnect cabling arrangement. The unused cross-connect panels or modules are re-usable for other circuits or other location...

Ngày tải lên: 20/12/2013, 22:15

... Distribution Frame 2 www .adc. com • + 1-9 5 2-9 3 8-8 080 • 1-8 0 0-3 6 6-3 891 Benefits • Lower operating costs. As compared to direct connect or interconnect designs, the EDF cross- connect reduces the time it ... Frame 3 www .adc. com • + 1-9 5 2-9 3 8-8 080 • 1-8 0 0-3 6 6-3 891 Permanent Equipment Cables, providing permanent connections between the EDF and dist...

Ngày tải lên: 09/12/2013, 16:15

... panel, and the means to terminate the cable into the patch panel — whether the terminations into the patch panel involve “punchdown” cable terminations, pre-made telco-type multi-pair cable ends, or ... room to the work area wall outlet. The typical gauge for Category 5e cable is 24 AWG. Category 6 is 23 AWG - the larger conductor diameter improves attenuation characteristics and sign...

Ngày tải lên: 10/12/2013, 02:15

... 2004 ADC Telecommunications, Inc. All Rights Reserved Web Site: www .adc. com From North America, Call Toll Free: 1-8 0 0-3 6 6-3 891 • Outside of North America: + 1-9 5 2-9 3 8-8 080 Fax: + 1-9 5 2-9 1 7-3 237 ... packet fiber connectors promise to bring back a little sanity and manageability to cable runs and equipment racks. However, high density fiber patch panel...

Ngày tải lên: 10/12/2013, 02:15

... of IEC 6128 0-4 -1 Similar to Method C of TIA/EIA 52 6-1 4-A 1-Test Cord Method of Reference Setting = Cl 9.1.2 of ISO/IEC 1476 3-3 Ed2 Similar to Method 2 of IEC 6128 0-4 -1 Similar to Method B of ... Reference to Reference Connector is 0.10 dB MMF and 0.20 dB SMF Mated Reference to Non-Reference Connector is 0.30 dB MMF and 0.50 dB SMF Mated Non-Reference to Non-...

Ngày tải lên: 10/12/2013, 02:15

... distance is critical to choosing fiber today that will support requirements in the future. Laser-optimized 50µm multimode fiber offers many benefits for both today's and tomorrow's network ... you can install laser- optimized fiber today for use with slower data rates, and when the need for more bandwidth arises, you only need to upgrade electronics to VCSEL-based transce...

Ngày tải lên: 10/12/2013, 02:15

... microns. To achieve acceptable yields, the maximum permissible apex offset needs to be greater than 50 microns. 65 microns will allow manufacturers to achieve high yields while allowing connectors to ... sense to increase the maximum apex offset to 65 microns as it will not inhibit connector performance and greatly increases manufacturing yields. A method to achieve lower apex o...

Ngày tải lên: 10/12/2013, 02:15