Tài liệu TRANH TV1-TAP 2 (6)

... __________________________________________________________________________ 2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. c. If the answer is no for either ... typing exit and turn the router off. 3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 7 .2. 6 Troubleshooting...

Ngày tải lên: 11/12/2013, 14:15

... v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. 3 - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. 12 Step 6 Remove ... - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 7 .2. 6 Spanning Tree Recalculation Objective • Create a basi...

Ngày tải lên: 11/12/2013, 14:15

... password Enable/VTY/Console passwords Router 1 GAD 1 72. 16.0.1 DCE 1 72. 17.0.1 25 5 .25 5.0.0 class cisco Router 2 BHM 1 72. 18.0.1 DTE 1 72. 17.0 .2 255 .25 5.0.0 class cisco Objective • Set up an IP addressing ... by typing exit and turn the router off. 2 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7 .2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 7 .2. 6 T...

Ngày tải lên: 11/12/2013, 14:15

... 2 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc. Step 2 Configure the routing protocol on ... RIP Version 2 Routing Enable version 2 of the RIP routing protocol on the Gadsden router only. 1 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco ... Routing v 3.0 - Lab 1...

Ngày tải lên: 21/12/2013, 19:15

... 2 - 2 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc. • Several Ethernet cables, straight-through ... information below. Record the AUI port numbers if the router is a Cisco 25 00 series router. Router Port Port Step 2 Identify the proper cables and connect router a. The connection between ... router labeled 10/100 Ethernet. T...

Ngày tải lên: 21/12/2013, 19:15

... _________________ _________________ _________________ _________________ 2 - 2 CCNA 1: Networking Basics v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc.

Ngày tải lên: 21/12/2013, 19:15

... _______________________________ 2 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 1 .2. 6 Troubleshooting RIP Version 2 using Debug Objective ... Version 2 Routing Enable version 2 of the RIP routing protocol on the Gadsden router only. Step 12 Start the debug function again on the GAD router a....

Ngày tải lên: 21/12/2013, 19:15

... 2 - 2 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc. d. Identify the Ethernet ports ... information below. Record the AUI port numbers if you are working with a Cisco 25 00 series router. Router Port Port Step 2 Identify the proper cables and connect router a. The connection between ... designation on the router to a port...

Ngày tải lên: 21/12/2013, 19:15

... one and doubles, base 2, for each position to the left. 8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1 Steps 1. Enter the binary bits in row three. For example 10111001 2. Put the decimal values ... 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 1 .2. 6 Copyright  20 03, Cisco Systems, Inc. Lab 1 .2. 6 Binary to Decimal Conversion Objective • ... bits, can range from 0...

Ngày tải lên: 21/12/2013, 19:15

... Step 2 Configure the workstations a. The configuration for the host connected to the Gadsden Router is: IP Address 1 92. 168.14 .2 IP subnet mask 25 5 .25 5 .25 5.0 Default gateway 1 92. 168.14 .2 b. ... for the host connected to the Birmingham Router is: IP Address 1 92. 168.16 .2 IP subnet mask 25 5 .25 5 .25 5.0 Default gateway 1 92. 168.16.1 Step 3 ping from the workstati...

Ngày tải lên: 21/12/2013, 19:15