Handbook of Mechanical Engineering Calculations P1

... Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright © ... reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 1.4 POWER GENERATION Deaerator H-p turbine H...

Ngày tải lên: 09/11/2013, 04:15

... website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 11.10 PLANT AND FACILITIES ENGINEERING TABLE 2 Heat-Exchanger Fouling Factors* total resistance to heat transfer. Then U ϭ the reciprocal of ... tube manufacturer’s engineering data show that a finned tube of these dimensions has 5.8 ft 2 of area per linear foot (1.8 m 2 /lin m) of tube. To compute the line...

Ngày tải lên: 17/12/2013, 11:15

... the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Professor of Mechanical Engineering, ... the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Professor of Mecha...

Ngày tải lên: 17/12/2013, 11:15

... acceleration force (G), defined as multiples of gravity, is a function of the rotational speed of the bowl and the distance of the particle from the axis of rotation. In the centrifuge, the centrifugal ... reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 13.30 ENVIRONMENTAL CONTROL basin in...

Ngày tải lên: 25/12/2013, 23:18

... Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 14.10 ENVIRONMENTAL CONTROL TABLE 3 Effect of Submergence on Efficiencies of Air Lift* Ratio D / h 8.70 5.46 ... known of the efficiency of the average air-lift installation in small waterworks. Tests show efficiencies in the neighborhood of 45 percent for depths of 50 ft (15 m) down to 20...

Ngày tải lên: 25/12/2013, 23:18

... (2.1 cm /m) of length? Calculation Procedure: 1. Sketch the building roof Figure 13 shows the building roof and machinery room roof. Indicate on the sketch the major dimensions of the roof and machinery ... replacement of existing water closets which use excessive amounts of water, in view of today’s new environmental laws and regulations. A further benefit of the ULF units is the...

Ngày tải lên: 25/12/2013, 23:18

... of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS HEATING, VENTILATING, AND AIR CONDITIONING 16.133 TABLE 32 Flow of Air in Natural-Draft Flues, ft 3 /(min ⅐ ft 2 )[m 3 /(min ⅐ m 2 )]* (53.3-cm) ... W). 4. Compute the total heat loss of the building The total heat loss of a building is the sum of the individual heat losses of the wa...

Ngày tải lên: 25/12/2013, 23:19

... (www.digitalengineeringlibrary.com) Copyright © 2006 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING ... intake and return passages of the solar system. The wheels permit the transfer of thermal energy from the return to the intake side of the system and offer a means o...

Ngày tải lên: 25/12/2013, 23:19

... (www.digitalengineeringlibrary.com) Copyright © 2006 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING ... diameter Use the speed ration of the shafts to determine the diameter of the small sheave. The speed ratio of the shafts is the ratio of the speed of the high-spe...

Ngày tải lên: 25/12/2013, 23:19

... reserved. Any use is subject to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 2.2 POWER GENERATION River flow River flow FIGURE 1 a. Once-through ... the quantity of steam, lb m /h (kg/h), lost from the condenser. Calculation Procedure: 1. Compute the mass rate of flow per hour of the air leakage The mass rate of flow per...

Ngày tải lên: 09/11/2013, 04:15