Variable Pitch Conical Spring Pro/ENGINEER Wildfire 2 0

... ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Conical Spring Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata START CREATING A NEW PART Create a part named con _spring ... the trajectory inclined line. Right click, and select Edit. Pick PITCH1 .00 and change the value of the pitch to [1.5]. Select the to Regenerate to see the effe...

Ngày tải lên: 06/11/2013, 00:15

... The revolved angle is 30 degrees. RIGHT datum plane 1 ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Helical Extension Spring Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata ... Double click PITCH1 .00 , and change the value 0. 5. Pick the Regenerate icon . Pick the trajectory. 20 4 Sketch a circle with diame...

Ngày tải lên: 06/11/2013, 00:15

... 1 ME-4 30 Introduction to Computer Aided Design ARM BRACKET - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata In a system window, create a new directory called ME-4 30 (e.g. H:\PTC_Working_Dir\ME-4 30) . ... Horizontal: 10 Vertical: 12. 5 This placement references can be verified by clicking the Placement tab. Click . 6...

Ngày tải lên: 27/10/2013, 17:15

... select appropriate dimensions as shown below – The HEIGHT distance 3 .00 0; the overall WIDTH 4 .00 0 and bottom RADIUS 8 .00 0 of balancing body. The three dimensions are highlighted in red. ... Close. 27 17 The conclusions that can be drawn from the graphs: • The shoulder distance is greater than 0 .25 for the entire range of height values (2 – 3 .2...

Ngày tải lên: 12/12/2013, 12:15

... the same technique to create a 45º x 0. 02 in. chamfer on the edges shown below. Second chamfer: 45º x 0. 02 Second chamfer: 45º x 0. 02 10 In the dashboard, click the Remove ... of decimal places to 4. Change the Nominal Value to 1 . 20 20. Change the Upper tolerance to 0. 000 6 and the Lower tolerance to 0. Select OK from the dialog box. ......

Ngày tải lên: 12/12/2013, 12:15

... 21 Click , and then pick to complete the sweep. 1 ME-4 30 Introduction to Computer Aided Design TRAY - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata ... modify the dimension as shown. 5 Click . Type in 12 for the depth of extrusion. Click . 20 Select Traj. Tangnt Chain Pick the outer...

Ngày tải lên: 12/12/2013, 12:15

... class="bi x1 y0 w2 h1" alt=""

Ngày tải lên: 23/02/2014, 08:20

... ■ SPRING AOP 2. 0 115 9187ch04.qxd 8/1 /07 4:41 PM Page 115 Spring AOP 2. 0 W elcome to the chapter on the future of Spring AOP. In Chapter 3, we described how Spring AOP has been used up to the Spring ... typing? CHAPTER 4 ■ SPRING AOP 2. 0 122 9187ch04.qxd 8/1 /07 4:41 PM Page 122 The Proxying Process In the example in Listing 4-5, we configured three beans to be l...

Ngày tải lên: 05/10/2013, 05:20

... Variables 23 2 A .2. 4 Expressions 23 2 A .2. 5 Statements 23 3 A .2. 6 Namespaces 23 5 A .2. 7 Classes 23 5 A .2. 8 Structs 23 7 A .2. 9 Arrays 23 7 A .2. 10 Interfaces 23 7 A .2. 11 Enums 23 8 A .2. 12 Delegates 23 8 A .2. 13 ... Keywords 22 9 A.1.8 Literals 22 9 A.1.9 Operators and Punctuators 23 0 A.1. 10 Preprocessing Directives 23 0 A .2 Syntactic Grammar 23 1 A ....

Ngày tải lên: 20/08/2012, 11:57

... www.dohoavn.net Hướng dẫn sử dụng Canopus Pro 2. 0 trong Adobe Premier Pro 2. 0 (để nén file và ghi đĩa) Trước hết, yêu cầu là bạn phải cài đặt Canopus Pro 2. 0 vào chương trình AP Sau khi bạn đã ... muốn lưu file Sau đó bạn nhấn nút Start để thực hiện công việc nén. Đến khi nào hết 100 % là hoàn tất công việc. Chúc các bạn thành công. Ghi chú : Trong AP thì b...

Ngày tải lên: 27/08/2012, 11:48