Variable Pitch Helical Extension Spring Pro/ENGINEER Wildfire 2 0

... The revolved angle is 30 degrees. RIGHT datum plane 1 ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Helical Extension Spring Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata ... Double click PITCH1 .00 , and change the value 0. 5. Pick the Regenerate icon . Pick the trajectory. 20 4 Sketch a circle with d...

Ngày tải lên: 06/11/2013, 00:15

... ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Conical Spring Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata START CREATING A NEW PART Create a part named con _spring ... the trajectory inclined line. Right click, and select Edit. Pick PITCH1 .00 and change the value of the pitch to [1.5]. Select the to Regenerate to see the effect...

Ngày tải lên: 06/11/2013, 00:15

... 1 ME-4 30 Introduction to Computer Aided Design ARM BRACKET - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata In a system window, create a new directory called ME-4 30 (e.g. H:\PTC_Working_Dir\ME-4 30) . ... Horizontal: 10 Vertical: 12. 5 This placement references can be verified by clicking the Placement tab. Click . 6...

Ngày tải lên: 27/10/2013, 17:15

... select appropriate dimensions as shown below – The HEIGHT distance 3 .00 0; the overall WIDTH 4 .00 0 and bottom RADIUS 8 .00 0 of balancing body. The three dimensions are highlighted in red. ... Close. 27 17 The conclusions that can be drawn from the graphs: • The shoulder distance is greater than 0 .25 for the entire range of height values (2 – 3 .2...

Ngày tải lên: 12/12/2013, 12:15

... the same technique to create a 45º x 0. 02 in. chamfer on the edges shown below. Second chamfer: 45º x 0. 02 Second chamfer: 45º x 0. 02 10 In the dashboard, click the Remove ... of decimal places to 4. Change the Nominal Value to 1 . 20 20. Change the Upper tolerance to 0. 000 6 and the Lower tolerance to 0. Select OK from the dialog box. ......

Ngày tải lên: 12/12/2013, 12:15

... 21 Click , and then pick to complete the sweep. 1 ME-4 30 Introduction to Computer Aided Design TRAY - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata ... modify the dimension as shown. 5 Click . Type in 12 for the depth of extrusion. Click . 20 Select Traj. Tangnt Chain Pick the outer...

Ngày tải lên: 12/12/2013, 12:15

... class="bi x1 y0 w2 h1" alt=""

Ngày tải lên: 23/02/2014, 08:20

... ■ SPRING AOP 2. 0 115 9187ch04.qxd 8/1 /07 4:41 PM Page 115 Spring AOP 2. 0 W elcome to the chapter on the future of Spring AOP. In Chapter 3, we described how Spring AOP has been used up to the Spring ... typing? CHAPTER 4 ■ SPRING AOP 2. 0 122 9187ch04.qxd 8/1 /07 4:41 PM Page 122 The Proxying Process In the example in Listing 4-5, we configured three beans to be l...

Ngày tải lên: 05/10/2013, 05:20

... xmlns:beans="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org / 20 01 /XMLSchema-instance" xsi:schemaLocation="http://www.springframework.org/schema/beans \ http://www.springframework.org/schema/beans /spring- beans-3 .0. xsd ... http://www.springframework.org/schema/beans /spring- beans-3 .0. xsd http://www.springframework.org/schema...

Ngày tải lên: 22/02/2014, 15:20

... shown. P. Vatter et al. Variable C-terminus of GRK6 mediates autoregulation FEBS Journal 27 2 ( 20 05 ) 603 9– 605 1 ª 20 05 The Authors Journal compilation ª 20 05 FEBS 604 3 at 300 00 0 g for 30 min at 4 °C. The ... indicated. Variable C-terminus of GRK6 mediates autoregulation P. Vatter et al. 604 4 FEBS Journal 27 2 ( 20 05 ) 603 9– 605 1 ª 20 05 The Authors Journal compi...

Ngày tải lên: 07/03/2014, 12:20