Lab 3 1 3 Resistance Measurement

... 1 - 3 CCNA 1: Networking Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1 .3 Resistance Measurement Objective • Demonstrate the ability to measure resistance and ... Measure Set Selector and Range Scale to Resistance Reading 10 00 Ω Resistor 10 kΩ Resistor 3 - 3 CCNA 1: Networking Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03,...

Ngày tải lên: 27/10/2013, 07:15

... 1 - 3 CCNA 1: Networking Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1 .3 Resistance Measurement Objective • Demonstrate the ability to measure resistance ... small resistances are measured. The instructions provided are for the Fluke 11 0 and 12 B. Other meters will function in a similar way. 2 - 3 CCNA 1: Networking Basi...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 3 CCNA 1: Networking Basics v 3. 0 - Lab 3. 1. 2 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1. 2 Voltage Measurement Objective • Demonstrate ... approximately 12 0 volts of AC directly to any electrical appliance that is plugged in. Examples of appliances are a computer, 2 - 3 CCNA 1: Networking Basics v 3. 0 - Lab 3. 1. 2 Copyright  20 03, Cisco ....

Ngày tải lên: 18/01/2014, 04:20

... 1 - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1 .3 Configuring Router Passwords Objective • ... Interface #1 Serial Interface #2 Interface #5 800 (806) Ethernet 0 (E0) Ethernet 1 (E1) 16 00 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1) 17 00 FastEthernet 0 (FA0) FastEthernet 1 (FA1) ... Seria...

Ngày tải lên: 23/10/2013, 00:15

... 1 - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1 .3 Configuring Router Passwords Objective ... GAD(config-line)#login GAD(config-line)#exit GAD(config)# 3 - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Step 7 Configure the enable password ... Passw...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 3. 1 .3 Configuring Router Passwords Objective ... GAD(config)#exit Step 8 Return to the user exec mode 3 - 6 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 3. 1 .3 Copyright  20 03, Cisco Systems, Inc. GAD#disable Step 9 Enter the privileged .....

Ngày tải lên: 18/01/2014, 04:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5 .1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 5 .1 .3 Using the Boot System Command Objective ... assignment before continuing. 2 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5 .1 .3 Copyright  20 03, Cisco Systems, Inc. Step 1 Login to the router a. Connect to the router and login. Step 2 ... _____...

Ngày tải lên: 18/01/2014, 04:20

... 1 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5 .1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 5 .1 .3 Using the Boot System Command Objective ... passwords Router 1 AD class cisco 2 - 5 CCNA 2: Routers and Routing Basics v 3. 0 - Lab 5 .1 .3 Copyright  20 03, Cisco Systems, Inc. a. Enter enable at the command prompt. Step 3 Save the existing ......

Ngày tải lên: 18/01/2014, 04:20

... 1 - 2 CCNA 1: Networking Basics v 3. 0 - Lab 5 .1 .3 Copyright  20 03, Cisco Systems, Inc. Lab 5 .1 .3 Connecting Router LAN Interfaces ... RJ45 connectors on the router labeled 10 /10 0 Ethernet”. This identifier may vary depending on the type of router used. A 2500 series router will have an AUI DB15 Ethernet or Crossover cable ... Start this lab with the comp...

Ngày tải lên: 24/01/2014, 19:20

Ngày tải lên: 10/11/2013, 01:11