Configuring Static NAT Addresses
Configuring Static NAT Addresses
... 1.1.4c Configuring Static NAT Addresses Objective • Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. ... interfaces with respect to NAT. To do this, use the ip nat inside or ip nat outside command. Step 11 Configuring Static Mapping a. Workstation #1, 10.10.10.10/24, wi...
Tài liệu Lab 1.1.4c Configuring Static NAT Addresses docx
...
Lab 1.1.4c Configuring Static NAT Addresses
Objective
• Configure a router to use network address translation (NAT) to convert internal IP addresses,
typically private addresses, into ... interfaces with
respect to NAT. To do this, use the ip nat inside or ip nat outside command.
Step 11 Configuring Static Mapping
a. Workstation #1, 10.10.10.10/24, will be design...
Tài liệu Lab 6.2.4 Configuring Static MAC Addresses pdf
... Cisco Systems, Inc.
Lab 6.2.4 Configuring Static MAC Addresses
Objective
• Create a static address entry in the switch MAC table.
• Remove the created static MAC address entry.
Background/Preparation ... MAC addresses are there now?
___________________________________
c. How many static addresses are there?
__________________________________________
d. Under what...
Tài liệu Lab 6.1.6 Configuring Static Routes doc
... 3.0 - Lab 6.1.6 Copyright 2003, Cisco Systems, Inc.
Lab 6.1.6 Configuring Static Routes
Objective
• Configure static routes between routers to allow data transfer between routers ... Copyright 2003, Cisco Systems, Inc.
the Configuring router passwords lab. Configure interfaces and IP host tables. If there are any
difficulties, refer to the Configuring Host Tables la...
Tài liệu Lab 6.1.6 Configuring Static Routes docx
...
Lab 6.1.6 Configuring Static Routes
Router
designation
Router
name
Enable
secret
password
Enable/VTY/ and
Console ...
Step 5 Adding static routes
a. How can this situation be changed so that the hosts can ping each other?
Add static routes to each router or run a routing protocol. This lab will add static routes. ... are any difficulties, refer to
the Config...
Tài liệu Lab 8.2.3 Configuring Static VLANs docx
... Intermediate Routing v 3.0 - Lab 8.2.3 Copyright 2003, Cisco Systems, Inc.
Lab 8.2.3 Configuring Static VLANs
Objective
• Create a basic switch configuration and verify it.
• Determine ...
1900:
Switch_A#config terminal
Switch_A(config)#interface Ethernet 0/2
Switch_A(config-if)#vlan static 2
Switch_A(config)#end
Step 9 Display the VLAN interface information
a. On S...
Tài liệu Lab 8.2.3 Configuring Static VLANs doc
...
Lab 8.2.3 Configuring Static VLANs
Objective
• Create a basic switch configuration and verify it.
• Determine ...
witch_A(config-if)#end
1900:
Switch_A#config t
Switch_A(config)#interface Ethernet 0/2
Switch_A(config-if)#vlan static 2
Switch_A(config)#end
Step 9 Look at the VLAN interface information
a. On Switch_A, ...
Switch_A(config-if)#end
1900:
Switch_A#confi...
Configuring NAT
... Lab 1.1.4a Configuring NAT Objective • Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. ... public IP addresses. Since the company has an internal requirement for more than 30 addresses, the IT manager has decided to implement NAT. The addresses 199.99.9.33 – 199.99.9.39 for s...
Lab 1.1.4a Configuring NAT
... Lab 1.1.4a Configuring NAT Objective • Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. ... public IP addresses. Since the company has an internal requirement for more than 30 addresses, the IT manager has decided to implement NAT. The addresses 199.99.9.33 – 199.99.9.39 for s...
Tài liệu Lab 1.1.4b Configuring NAT doc
... Systems, Inc.
Lab 1.1.4b Configuring NAT
Objective
• Configure a router to use Port Address Translation (PAT) to convert internal IP addresses,
typically private addresses, into an outside ... the ip nat inside or ip nat outside command:
Gateway(config)#interface fastethernet 0
Gateway(config-if)#ip nat inside
Gateway(config-if)#interface serial 0
Gateway(config...