Configuring a Router

... Interface Serial0, changed state to up • Enables an interface that is administratively shut down Router# configure terminal Router( config)#interface serial 0 Router( config-if)#shutdown %LINK-5-CHANGED: ... Interface Serial0, changed state to administratively down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down • Administratively turns off an interface Disab...

Ngày tải lên: 08/07/2013, 01:27

... ## ## Router( config)# # is known as a delimiting character. The delimiting character must surround the banner message and can be any character so long as it is not a character used within ... tt tt ee ee rr rr mm mm ii ii nn nn aa aa ll ll Router( config)# Moves to global configuration mode. This prompt indicates that you can start making changes. Router( config)#hh hh oo oo...

Ngày tải lên: 19/10/2013, 00:20

... v2.0—3-15 Summary • STP is a bridge-to-bridge protocol used to maintain a loop-free network. • STP establishes a root bridge, a root port, and designated ports. • With STP, the root bridge has the lowest ... bridge ID, which is made up of the bridge’s priority and MAC address. • With STP, ports transition through four states: blocking, listening, learning, and forwarding. • If a cha...

Ngày tải lên: 08/07/2013, 01:27

... firewall's General Status page. You'll also visit this page whenever you need to activate a new service or reactivate a service after clearing a firewall's configuration; this is rare, ... to activate various features, and they'll be needed again if you ever have to clear the firewall. 212 The Registration Status page shows the registration status and activation code...

Ngày tải lên: 29/09/2013, 13:20

... Configuring a gateway to gateway VPN is easy using ISA Server. The reason why it’s so easy is that the Local and Remote VPN Wizards make the setup a virtual no-brainer. Well, it’s a no-brainer ... Storage Location page, accept the defaults for where you want to put the Certificate database and Certificate Database Log. You have the option to Store configuration information in a shar...

Ngày tải lên: 18/10/2013, 14:15

... Using Linux as a Router Jonathan Feldman Linux can be a terrific "poor man’s" router. It takes a little more startup configuration than a typical hardware router, but once it ... the router maintain the routing table? In two ways: statically and dynamically. Static routes are added by you, in a known, and sometimes tedious, fashion. Typically, default routes are stat...

Ngày tải lên: 18/10/2013, 17:15

... even interarea summaries. Capetown just needs a default route to the ABR, SanJose3. By configuring Area 2 as a stub area, SanJose3 automatically propagates a default route into Area 2. Use ... DoNotAge external LSA 0 Number of areas in this router is 1. 0 normal 1 stub 0 nssa External flood list length 0 Area 2 Number of interfaces in this area is 2 It is a stub are...

Ngày tải lên: 27/10/2013, 08:15

... a. Enter the command show interface serial 0 on GAD. Refer to interface chart. GAD#show interface serial 0 This will show the details of interface serial 0. b. List at least three details ... global configuration mode and configure the hostname as shown in the chart. b. Configure the console, virtual terminal and enable passwords. If there are any problems, refer to the Lab 3.1.3...

Ngày tải lên: 05/11/2013, 12:15

... console cables. Step 2 Configure the name and passwords for Router 1 Router Designation Router Name Interface type Serial 0 Address Subnet mask Enable secret password Enable/VTY/Consol e ... this lab assignment before continuing. Step 1 Basic Router Configuration a. Configure the router. Connect the routers as shown in the diagram. This lab requires a null serial cabl...

Ngày tải lên: 11/12/2013, 13:15

... a PC to a router and switch using the proper cable • Configure HyperTerminal on the PC • Observe the router and switch user interface Background / Preparation This lab will focus on the ability ... terminal is a DB-25, an RJ-45 to DB-25 adapter will be needed. Both of these adapters typically come with a Cisco router or switch. Step 4 Locate or build a rollover cab...

Ngày tải lên: 21/12/2013, 19:15