Máy đào HuynDai R170W-9 (Phần 7) - P6 4
Máy đào HuynDai R170W-9 (Phần 7) - P6.4
... between CN-142 (B) -CN-7 (15)Open circuit or poor connection between CN-142 (A) -CN-7 (14) or CN-142 (C )- CN-7 (16)Open circuit or poor connection between CN-7 (14) -CN-16 (3) or CN-7 (16 )- CN-16 ... between CN-1 (3)-CD-42 (B)Short circuit or poor connection between CD-42(A)-CN-1 (2) or CD-42 (C)-CN-1 (4)Short circuit or poor connection between CN-1 (2)-CN-51(4) or CN-1 (4) - N-51...
Ngày tải lên: 30/10/2012, 10:11
Máy đào HuynDai R250 - P5.7
... is canceled- Coolant temperature : Less than 100°C- Engine rpm drop to accel dial 7 position- Overheat warning lamp & buzzer : ON- Return to the mode and accel dial set before- Hold on the ... FUNCTIONActuatedCanceledOverheat warning lamp- Coolant temperature : Above 110°C- Accel dial set : Above 8- Coolant temperature : Less than 100°C- Changed mode set by operator※ If any of the ......
Ngày tải lên: 27/10/2012, 10:56
Máy đào HuynDai R170W-9 (Phần 7) - P6.1
... -- -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - 6-1 Group 2 Hydraulic and Mechanical System -- -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- ... -- -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - --...
Ngày tải lên: 30/10/2012, 10:10
Máy đào HuynDai R170W-9 (Phần 7) - P6.2
... cylinder fully retracted and arm cylinder rod retracted almost in full.1.17W96TS01(210 -7 ) 6-2 0(2)17W96TS02 6-2 37. FRONT AXLE AND REAR AXLE7. FRONT AXLE AND REAR AXLEProblem Cause CorrectionInsufficient ... replace- ment hours?Replace hydraulic oil to be specified.Flush with hydraulic oil and replace return filter.Has return filter been replaced at proper intervals?Cause RemedyCause...
Ngày tải lên: 30/10/2012, 10:10
Máy đào HuynDai R170W-9 (Phần 7) - P6.3
... CN-21 (2)-CN-21 (6)Check continuity between CN-141 (2)-CN-98 (3), CN-141 (9)-CN-97 (10), CN-141 (10)-CN-98 (5), CN-141 (5)-Chassis , CN-141 (1)-CN-21 (5), CN-141 (3)-CN-21 (6), CN-141 (4)-CN-21 ... MOTOR1278CN-2START RYCR-23ANTI-RESTART RYCR-51234521534ANTI-RESTART RY15MCUCN-52BATT RYCR-1BATTERYDO-121CN-6021CN-95MASTER SW21CS-74DIODEPOWER RYCR-35ECM POWER RYCR-451234521534596036CN-5131415CN-3...
Ngày tải lên: 30/10/2012, 10:11
Máy đào HuynDai R170W-9 (Phần 2) - Chapter 4
... S82 2-0 14000 -CR-29 - 5 Travel forward relay - -CR-30 - 5 Travel reverse relay - -CR-35 - 5 Power relay - -CR-36 - 5 Preheat relay - -CR-45 - 5 ECM power relay - -CR-46 - 4 Fuel warmer relay - -CR-47 - ... solenoid relay - -CR-62 - 5 Breaker relay - -CR-66 - 5 Parking relay - -CR-78 - 4 Head lamp power relay -...
Ngày tải lên: 27/10/2012, 08:16
Máy đào HuynDai R250 - P6.4
... repair Replace Replace Replace 12 11 CN-2 CN-76 CPU CONTROLLER CN-50 12 1 2 CD-17 TACHO SENSOR ACCEL ACTUATOR 1 2 3 4 5 6 M P+ SIG P- NC M+ M- 2 1 3 5 6 CN-51 20 21 22 25 26 23 rpm 5 7 CN-9 A B C + S - CN- 142 ACCEL DIAL Wiring ... machine. (2) ① ② ③ ④ ⑤ ⑥ ⑦ (29 0-7 TIER) 6-3 9(1) 6 -4 3 Wiring diagram 12 11 CN-2 CN-76 CPU CONTROLLER CN-50 12 1 2 CD-17 TACHO SENSOR ACCEL ACTUATOR...
Ngày tải lên: 27/10/2012, 10:56
Shop manual máy đào HuynDai R170W-9 (Phần 5) - P5.4
... over 8- Power mode : P- Accel dial power : 9- Power boost solenoid : ON- Power boost pilot lmap : ON- Operating time : max 8 secondsCanceled Power boost switch : OFF- Pre-set power mode - Power ... 5-7 GROUP 4 POWER BOOST SYSTEM GROUP 4 POWER BOOST SYSTEM Main pumpPilot pumpEngineECMCANMCUAccel dial Accel dial signalNormalCN-16EmergencyCN-16ACN-16BClusterMain control ... max 8 sec...
Ngày tải lên: 29/10/2012, 15:07
Shop manual máy đào HuynDai R170W-9 (Phần 5) - P5.7
... stepwarningActivated- Coolant or hydraulic oil temperature : Above 100˚C--Warning lamp & buzzer : ONPump absorption torque is reduced.Canceled- Coolant or hydraulic oil temperature : Less than 95˚C- Return ... temperature : Less than 95˚C- Return to pre-set the pump absorption torque.Second stepwarningActivated- Coolant or hydraulic oil temperature : Above 105˚C--Emergency warning lamp po...
Ngày tải lên: 29/10/2012, 15:07
Máy đào HuynDai R170W-9 (Phần 6) - P2.4
... N.A M14×1.5 - 12M1 Gauge port M14×1.5 - 12X1 Pilot pressure port M14×1.5 - 12X2Pilot pressure portM14×1.5 - 11.5T1 Drain port PF 3/4 - 17T2 Drain port PF 3/4 - 12U Flushing port PF 1/2 - 16S Make ... Flushing port PF 1/2 - 16S Make up port M27×2.0 - 16MA, MBGauge port M18×1.5 - 12M2, M3 Gauge portM10×1.0 - 8Gext Brake release port M12×1.5 - 12.5...
Ngày tải lên: 30/10/2012, 08:48