Máy đào HuynDai R170W-9 (Phần 6) - P2 7

... spring 9 Spring retainer 10 O-ring 11 O-ring 12 Oil seal 13 Spring Guide 14 Snap ring 15 DU bushing 16 Pedal plate 17 Pedal assy 1 7-1 Pedal 1 7-2 Lock plate 1 7-3 Hex bolt 1 7-4 Plain washer 18 Pedal ... BRAKE PEDALGROUP 7 BRAKE PEDAL (VALVE)131171231329815281 7-2 P2BR2T2P1T1BL2BR1BL1527204102661412933021624292221231 7-1 172518191 7-4 1 7-3 1 Lower body 2 Upper body 3 Spool 4...

Ngày tải lên: 30/10/2012, 08:48

... upfunction is canceled- Coolant temperature : Above 30°C- Mode : Default(S mode )- Warming up time : 10 minutes(Max )- Warming up lamp : ON- Default mode- Default mode- Changed mode- Warming up lamp ... lamp- Coolant temperature : Less than 30°C(After engine run )- Accel dial position is under 3- Coolant temperature : Above 30°C- Warming up time : Above 10 minutes- Changed mode se...

Ngày tải lên: 27/10/2012, 10:56

... -- -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - 2-5 8Group 5 RCV Lever -- -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- - -- ... -- -- -...

Ngày tải lên: 30/10/2012, 08:48

... O-ring 61 O-ring 62 O-ring 63 O-ring 64 O-ring 65 O-ring 66 O-ring 67 O-ring 68 O-ring 69 O-ring 70 O-ring 71 O-ring 72 O-ring 73 O-ring 74 Backup-ring 75 Backup-ring 76 Backup-ring 77 Backup-ring ... Plug-relief cat 37 Plug-relief cat 38 Plug-bucket 39 Plug-bucket parallel 40 Plug-option 41 Plug-orifice 42 Plug 43 Load check-poppet 44 Load check-poppet 45 Signal-poppet 46 Travel straight-sle...

Ngày tải lên: 30/10/2012, 08:48

... piston 18 O-ring 19 O-ring 20 Brake spring 21 Rear cover 22 Needle bearing 23 Pin 24 Valve plate 25 Wrench bolt 26 Plug 27 Back up ring 28 O-ring 29 Spring 30 Check 31 Relief valve 32 Anti-inversion ... valve 33 Time delay valve 34 Wrench bolt 35 Plug 36 O-ring 37 Plug 38 Plug 39 Plug 40 Name plate 41 Rivet 42 Level gauge 43 Plug 44 O-ring 45 O-ring 46 Back up ring37313933,34 38253235,3645444...

Ngày tải lên: 30/10/2012, 08:48

... N.A M14×1.5 - 12M1 Gauge port M14×1.5 - 12X1 Pilot pressure port M14×1.5 - 12X2Pilot pressure portM14×1.5 - 11.5T1 Drain port PF 3/4 - 17T2 Drain port PF 3/4 - 12U Flushing port PF 1/2 - 16S Make ... Flushing port PF 1/2 - 16S Make up port M27×2.0 - 16MA, MBGauge port M18×1.5 - 12M2, M3 Gauge portM10×1.0 - 8Gext Brake release port M12×1.5 - 12.5...

Ngày tải lên: 30/10/2012, 08:48

... composed of the spool (4), spring (6) for setting secondary pres-sure, return spring (10), stopper (8), spring seat (7, 13) and shim (5). The spring for setting the sec-ondary pressure has been generally ... pump 4 Main control valve 5 Hydraulic motor 6 Hydraulic cylinder11PT3234563)3) 2-7 0 2-7 0The force of the spring (6) that determines the output pressure of the pilot valve is not...

Ngày tải lên: 30/10/2012, 08:48

... 2-7 21. STRUCTURE1. STRUCTUREThe casing has the oil inlet port P (primary pressure), and the oil

Ngày tải lên: 30/10/2012, 08:48

... socket bolt 26 Plug 27 Spacer 28 O-ring 29 Hexagon socket bolt 30 Plug 25 7 21 22 20 19 14 15 12 1 24 5 23 4 17 15 13 11 18 30 9, 10 16 2 3 27 28 29 6 826 (290LC -7 ) 2 -7 4 2 -7 8 2. FUNCTION FUNDAMENTAL ... Forward) Travel(LH, Backward) Travel(RH, Forward) Travel(RH, Backward) Port size PF 1/4 (290LC -7 ) 2 -7 3 2 -7 7 CROSS SECTION The construction of the RCV pedal is show...

Ngày tải lên: 27/10/2012, 10:55

... increased. Refer to page 2-3 7 for the arm regeneration function. 7. ARM REGENERATION CUT SYSTEM7. ARM REGENERATION CUT SYSTEM Pi1 Pi2 DR#, dr# B1 A1 A2 B2 B1 S2 S1 P2 P1 P1 B3 A3 A2 A1 T(dr1) Pd6 Pc6 T2,T3,T4 PO3 (MCV) P T2 ENG HYD TANK ACCELERATOR PEDAL ARM CYLINDER BUCKET CYLINDER TRAVEL ... 1 ARM REGEN BUCKET OPT-B DOZER ARM 2 P1 P4 P3 P2 PO(MCV) PG(S/M) LINE FILTER A(fw) B(bw) X...

Ngày tải lên: 27/10/2012, 11:04