Máy đào HuynDai R250 - P5 4

... relief valve set pressureTime of operationH or S330kgf/cm2-H360 kgf/cm2Even when pressed continuously,it is canceled after 8 sec.・・※Default - Power boost solenoid valve : OFF21075MS06 ... 5-7 GROUP 4 POWER BOOST SYSTEMMain control valveArm 1Boom 2SwingLH travelArm 2BucketBoom 1OptionRH

Ngày tải lên: 27/10/2012, 10:56

... 381SECTION A-ASECTION B-BSECTION C-C151 Needle roller161 Piston162 Shoe167 Pivot171 Parallel pin193 Spring201 Valve202 Sleeve203 Spring retainer204 Plug205 Shim206 Spring208 O-ring209 O-ring210 O-ring211 ... socket plug355 O-ring357 Plug358 O-ring359 O-ring363 Spool368 Steel ball379 Filter380 Plug382 Plug383 O-ring384 O-ring385 Steel ball397 Orifice398 Hexagon socket plug399 Name plate219 O-r...

Ngày tải lên: 27/10/2012, 10:55

... R2FRONTPUMPREARPUMPMAKE UP VALVERELIEF VALVEBOOM HOLDING VALVEBUCKET CYLINDERBOOM CYLINDER25073HC11 3-1 5When the LH control lever is pulled back, the arm spools in the main control valve are ... R2FRONTPUMPREARPUMPXAa1XAa2XBa1XBa2Aa1Ba1PaLXBa2XAa2ARM1MAKE UPVALVERELIEFVALVEARM HOLDING VALVEBUCKET CYLINDERBOOM CYLINDER25073HC13 3-1 6When the LH control lever is pushed forward, the arm s...

Ngày tải lên: 27/10/2012, 10:55

... solenoidS81 6-0 06002S81 6-0 12002S81 6-0 08002S81 6-0 08002 2-8 526 2-1 S81 6-0 12002 2-8 526 2-1 A81 6-0 12002S81 6-0 02008DT06S-12SDT0 6-8 SDT0 6-2 S-P012S81 4-0 02100DT0 6-8 S3582 5-0 21192527 6-0 MG640605MG610070MG6100703582 5-0 211173852MWP01F-BMG64079521N 8-2 0041ST71026 4-2 S81 0-0 02202GP-8904693441110344111 0-- DT0 6-2 S-P012DT0 6-2 S-...

Ngày tải lên: 27/10/2012, 10:56

... LoadCurrent(mA)Current(mA)Pressure(kgf/cm2)Pressure(kgf/cm2)230±30280±30600±30700±30700±30245260600±30700±30700±302250±502150±501200±1001050±1001050±1002000190 0-- -2 15020501200±1001050±1001050±1001900180 0-- -4 7313535563135351008 5-- -HSAUTO DECELOne touch decelKEY STARTHigh powerStandard powerEngine ... more time.5)12345678910Segment( )High idle-900High idle-800High idle-700High i...

Ngày tải lên: 27/10/2012, 10:56

... 5-6 GROUP 3 AUTOMATIC DECELERATION SYSTEMP MFuel injectionpumpAccelactuatorMotor drive signalPotentiometer ... theresult of reducing the engine speed, fuel consumption and noise are effectively cut down during non-operation of the control levers.When the Auto decel lamp is turned off by pressing the switch or

Ngày tải lên: 27/10/2012, 10:56

... 5-8 GROUP 5 TRAVEL SPEED CONTROL SYSTEMTravel motorRegulatorRegulatorMain control valveArm 1Boom

Ngày tải lên: 27/10/2012, 10:56

... upfunction is canceled- Coolant temperature : Above 30°C- Mode : Default(S mode )- Warming up time : 10 minutes(Max )- Warming up lamp : ON- Default mode- Default mode- Changed mode- Warming up lamp ... lamp- Coolant temperature : Less than 30°C(After engine run )- Accel dial position is under 3- Coolant temperature : Above 30°C- Warming up time : Above 10 minutes- Changed mode se...

Ngày tải lên: 27/10/2012, 10:56

... is canceled- Coolant temperature : Less than 100°C- Engine rpm drop to accel dial 7 position- Overheat warning lamp & buzzer : ON- Return to the mode and accel dial set before- Hold on the ... FUNCTIONActuatedCanceledOverheat warning lamp- Coolant temperature : Above 110°C- Accel dial set : Above 8- Coolant temperature : Less than 100°C- Changed mode set by operator※ If any of the ......

Ngày tải lên: 27/10/2012, 10:56

... 5-1 1GROUP 8 ANTI-RESTART SYSTEMEngineCPU controllerStarterStart safety relayDrive signalCN-92aCN-92b1. ANTI-RESTART FUNCTIONAfter 10 seconds from the ... starter from inadvertent restarting.2. When a replacement or taking-off of the CPU controller is needed, connect CN-92a and CN-92b toensure the engine start without the CPU controller.21075MS10

Ngày tải lên: 27/10/2012, 10:56