CCNA P3 V3 Configuring a Catalyst Switch

16
324
0

Tài liệu Cisco Systems - Configuring a catalyst switch pdf

... vlan VLAN Name Status Ports 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, ... Dynamic All0090.273B.8 7A4 FastEthernet 0/26 Dynamic All00D0.588F.B600 FastEthernet 0/26 Dynamic All00D0.5892.38C4 FastEthernet 0/27 Dynamic AllManaging the MAC Address Table Catalyst 1900 Catalyst ... given a functioning access layer switch •Configure the switch management IP address and the default gateway, given a functioning access layer switch and an IP addressing scheme•Execute an add,...

26
714
0

CCNA P3 V3 Spanning-Tree Protocol Overview

16
427
2

CCNA - V3 P1 - Configuring Catalyst Switch Operations

15
281
1

CCNA - P3 - Starting a Switch

23
321
0

CCNA - P4 - Configuring a Router

37
283
0

Lab 6.2.9 Firmware Upgrade of a Catalyst 2900 Series Switch

... latest update for the Catalyst 2950. This has the same file name stem as the current image. However, for the purpose of the lab, assume that this is an update. The IOS update release contains ... Lab 6.2.9 Firmware Upgrade of a Catalyst 2900 Series Switch Objective • Create a basic switch configuration verify it. • Upgrade the IOS and HTML files from a file supplied ... instructor. Background / Preparation Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce...

4
337
0

Tài liệu Lab 6.2.8 Password Recovery Procedure on a Catalyst 2900 Series Switches ppt

... in CCNA 3 and CCNA 4 it is necessary to start with an unconfigured switch. Use of a switch with an existing configuration may produce unpredictable results. These instructions allow preparation ... terminal ALSwitch(config)#no enable secret ALSwitch(config)#enable password Cisco ALSwitch(config)#line console 0 ALSwitch(config-line)#password cisco ALSwitch(config-line)#exit ALSwitch(config)#line ... a password, enter class (if that does not work, ask the instructor). Switch& gt;enable 2. Remove the VLAN database information file. Switch# delete flash:vlan.dat Delete filename [vlan.dat]?[Enter]...

7
327
0

Tài liệu Lab 6.2.8 Password Recovery Procedure on a Catalyst 2900 Series Switches docx

... Lab 6.2.8 Password Recovery Procedure on a Catalyst 2900 Series Switches Objective • Create and verify a basic switch configuration verify it. • Change passwords to the password recovery ... the answer is no, troubleshoot the host and switch configurations. Step 4 Reset the console password a. Have a classmate change the console and VTY passwords on the switch. Save the changes ... Contact the Cisco TAC for the factory-installed password. 2. Provide the serial number and/or Media Access Control (MAC) address of the switch. The serial number is usually located on the back...

6
326
0

Tài liệu Lab 6.2.9 Firmware Upgrade of a Catalyst 2900 Series Switch doc

... enable. If prompted for a password, enter class (if that does not work, ask the instructor). Switch& gt;enable 2. Remove the VLAN database information file. Switch# delete flash:vlan.dat ... 3.0 - Lab 6.2.9 Copyright  2003, Cisco Systems, Inc. Erasing and Reloading the Switch For the majority of the labs in CCNA 3 and CCNA 4 it is necessary to start with an unconfigured switch. ... 5 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 6.2.9 Copyright  2003, Cisco Systems, Inc. Lab 6.2.9 Firmware Upgrade of a Catalyst 2900 Series Switch Objective • Create...

5
335
0