CCNA - P4 - Configuring a Router

... Router( config)#interface serial 0 Router( config-if)#shutdown %LINK-5-CHANGED: Interface Serial0, changed state to administratively down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to ... Seria0, changed state to up %LINEPROTO-5-UPDOWN: Line Protocol on Interface Serial0, changed state to up • Enables an interface that is administratively shut down Router# confi...

Ngày tải lên: 08/07/2013, 01:27

... encryption — Interface names — Moving between interfaces — Configuring a serial interface — Configuring a Fast Ethernet interface — Creating a message-of-the-day (MOTD) banner — Creating a login banner — ... PART III Configuring a Router Chapter 6 Configuring a Single Cisco Router 60 Setting the Clock Time Zone Creating a Message-of-the-Day Banner TIP: The MOTD banner is dis...

Ngày tải lên: 19/10/2013, 00:20

... v2.0— 3-1 5 Summary • STP is a bridge-to-bridge protocol used to maintain a loop-free network. • STP establishes a root bridge, a root port, and designated ports. • With STP, the root bridge has the lowest ... v2.0— 3-9 Spanning-Tree Path Cost © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0— 3-1 0 Spanning-Tree Example © 2002, Cisco Systems, Inc. All rights reserved....

Ngày tải lên: 08/07/2013, 01:27

... Catalyst 1900 Switch © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0— 1-9 Initial Bootup Output from the Catalyst 2950 Switch -- - System Configuration Dialog -- - At any point you may ... enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[ ]'. Continue with configur...

Ngày tải lên: 08/07/2013, 01:27

Ngày tải lên: 29/09/2013, 13:20

... Configuring a gateway to gateway VPN is easy using ISA Server. The reason why it’s so easy is that the Local and Remote VPN Wizards make the setup a virtual no-brainer. Well, it’s a no-brainer ... certificate that can give you a headache. In this lab we’ll put together a five computer VMware network that includes two VPN servers, a domain controller, a stand-alone root CA...

Ngày tải lên: 18/10/2013, 14:15

... Using Linux as a Router Jonathan Feldman Linux can be a terrific "poor man’s" router. It takes a little more startup configuration than a typical hardware router, but once it ... It supplies parameters: # interface-name tty-device speed local-ip-address remote-ip-address /etc/ppp/arp -d 167.195.160.115 # remove ppp’s Ethernet hardware type /etc/ppp/arp -t tr -s 167.195.1...

Ngày tải lên: 18/10/2013, 17:15

... even interarea summaries. Capetown just needs a default route to the ABR, SanJose3. By configuring Area 2 as a stub area, SanJose3 automatically propagates a default route into Area 2. Use ... commands on SanJose3, the ABR, to configure Area 2 as a totally stubby area: SanJose3(config) #router ospf 1 SanJose3(config -router) #no area 2 stub SanJose3(config -router) #area...

Ngày tải lên: 27/10/2013, 08:15

... 1 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.5 Copyright  2003, Cisco Systems, Inc. Lab 3.1.5 Configuring a Serial Interface Objective • Configure a serial interface ... this lab assignment before continuing. Step 1 Basic Router Configuration a. Configure the router. Connect the routers as shown in the diagram. This lab requires a null serial cab...

Ngày tải lên: 05/11/2013, 12:15

... the name and passwords for Router 2 3 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.5 Copyright  2003, Cisco Systems, Inc. a. On the Birmingham router, enter the global configuration ... this lab assignment before continuing. Step 1 Basic Router Configuration a. Configure the router. Connect the routers as shown in the diagram. This lab requires a null serial...

Ngày tải lên: 11/12/2013, 13:15