168535672 lab 3 band reject filter

... table: Vlan www.ipmac.com.vn Vlan Name Port Vlan Vlan Vlan Fa0/2 Fa0 /3 Fa0/4 The command vlan database can be used in the Privileged EXEC mode to enter into VLAN configuration mode A VLAN name ... Switch_A#vlan database Switch_A(vlan)#vlan vlan_number Switch_A(vlan)#exit Issue Show vlan to view configuration : Upon exiting, the VLAN is applied to the switch The next step is to assign the VL...

Ngày tải lên: 13/11/2012, 10:56

... the cable ends • An RJ-45 to DB9 female terminal adapter, available from Cisco • Cabling continuity tester • Wire cutters Step Use the table as a reference to help create a rollover console cable ... Step 10 Test the finished cable Have the instructor check it How is it possible to tell if the cable is functioning properly? 3-3 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9c Copyri...

Ngày tải lên: 16/10/2013, 20:15

... reload instructions at the end of this lab Perform those steps on all routers in this lab assignment before continuing 2-6 CCNA 4: WAN Technologies v 3.0 - Lab 3.3.3 Copyright  2003, Cisco Systems, ... steps, finish the lab by doing the following: • • Turn the router off • 4-6 Logoff by typing exit Remove and store the cables and adapter CCNA 4: WAN Technologies v 3.0 - Lab 3.3....

Ngày tải lên: 16/10/2013, 20:15

... the cable ends • An RJ-45 to DB9 female terminal adapter, available from Cisco • Cabling continuity tester • Wire cutters Step Use the table as a reference to help create a rollover console cable ... Step 10 Test the finished cable Have the instructor check it How is it possible to tell if the cable is functioning properly? 3-3 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9d Copyri...

Ngày tải lên: 19/10/2013, 02:15

... end of the cable using the 568-A scheme to finish the crossover cable 3-4 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9d Copyright  2003, Cisco Systems, Inc Step 11 Test the finished cable Have ... Solid wire is fine for cable runs that are punched down into jacks Step Strip 5.08 cm (2in.) of jacket off one end of the cable 2-4 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9d...

Ngày tải lên: 19/10/2013, 02:15

... encapsulation type to PPP by typing encapsulation ppp at the interface serial configuration mode prompt on both routers Brasilia(config-if)#encapsulation ppp Warsaw(config-if)#encapsulation ppp b What did ... v 3.0 - Lab 3.3.4 Copyright  2003, Cisco Systems, Inc • • Turn the router off • 4-6 Logoff by typing exit Remove and store the cables and adapter CCNA 4: WAN Technologies...

Ngày tải lên: 19/10/2013, 02:15

... Enter The router is ready for the assigned lab to be performed 5-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright  2003, Cisco Systems, Inc Router Interface Summary Router Ethernet ... logoff by typing exit Turn the router off 4-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright  2003, Cisco Systems, Inc Erasing and reloading the router Ent...

Ngày tải lên: 23/10/2013, 00:15

... the other end of the cable using the 568-A scheme to finish the crossover cable Step 11 Test the finished cable Have the instructor check it How is it possible to tell if the cable is functioning ... lengths for this cable are 1.83 m (6 ft) and 3.05 m (10 ft) 2-4 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9e Copyright  2003, Cisco Systems, Inc Step Cut a piece of stranded UTP...

Ngày tải lên: 23/10/2013, 00:15

Ngày tải lên: 23/10/2013, 00:15

... new password: Password changed DLSwitch1> (enable) set enablepass Enter old password: (Because you not currently have a password, just hit enter) Enter new password: Retype new password: Password ... Attempt to telnet into the Catalyst switch You will not be able to get in because you not know the passwords The Catalyst 4000 series of switches deals with password recovery m...

Ngày tải lên: 23/10/2013, 00:15

... Prior to starting the lab, the teacher or lab assistant should have one multimeter available for each team and various networking-related items for testing resistance Work in teams of two ... cable Step Select the Resistance Scale on the Multimeter Fluke 110: Resistance Measurements: Move the rotary selector to the Omega symbol for Ohms (Ω) in order to measure resistance Use the Ra...

Ngày tải lên: 27/10/2013, 07:15

... d Is show one of the options available? _ Step Display help for the show command a Enter the show ? command The router responds with the show subcommands available in ... the router prompt The router responds with all commands available in user mode b What did the router reply with? c Are all router commands available at the current prompt? ... three user mode show s...

Ngày tải lên: 27/10/2013, 07:15

Ngày tải lên: 27/10/2013, 07:15

... instructor or invent a message Reflection What issues arose as the communications system was being built, that apply to data communications between computers? ... _ _ 2-2 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9f Copyright  2003, Cisco Systems, Inc ... _ _ _ Analyze the communications system in terms of the OSI layers _

Ngày tải lên: 27/10/2013, 07:15

... WAN Technologies v 3.0 - Lab 3.3.5 Copyright  2003, Cisco Systems, Inc Step 10 Enter the command debug ppp negotiation on the Paris router a Enter the command debug ppp negotiation on the Paris ... passwords If there is a problem completing this, refer to the Network Address Translation (NAT) configuration lab Step Configure the Paris interface as listed Configure the Paris rout...

Ngày tải lên: 27/10/2013, 07:15