Migrating EIGRP to OSPF

... Availability Campus Network Design: Routed Access Layer using EIGRP or OSPF iv OL-9011-01 High Availability Campus Network Design— Routed Access Layer using EIGRP or OSPF Introduction This document ... High Availability Campus Network Design— Routed Access Layer using EIGRP or OSPF 20 OL-9011-01 Implementing Layer Access using O...

Ngày tải lên: 24/01/2014, 10:20

... www.it-ebooks.info Migrating Applications to IPv6 www.it-ebooks.info www.it-ebooks.info Migrating Applications to IPv6 Dan York Beijing • Cambridge • Farnham • Köln • Sebastopol • Tokyo www.it-ebooks.info Migrating ... starting to pay attention to IPv6, and given that many apps are just now moving to IPv6, this book will continue to evolve to address issues ident...

Ngày tải lên: 24/04/2014, 15:34

Ngày tải lên: 14/12/2021, 20:34

... Step As you migrate to EIGRP, you decide to leave RIP running on all the routers to avoid a loss of connectivity On SanJose1 and SanJose2, configure EIGRP for Autonomous System 24, as shown ... What is the metric of the connected routes? Step To complete the migration from RIP to EIGRP, you must disable RIP on all three routers Be sure to turn off debug before exiting...

Ngày tải lên: 24/01/2014, 19:20

... Router(config-if)#ip summary-address eigrpautonomous-systemnumber ip-address mask administrative-distance The EIGRP hello interval should be tuning to 10 seconds R1(config-if)#ip hello-interval eigrp 1000 10 ... Rx(config-if)#ip address 192.x.x.x 255.255.255.255 Rx(config)#router ospf Rx(config-router)#network 150.x.y.0 0.0.0.255 area Rx(config-router)#network 192.x.x.x 0.0.0.0 area Tas...

Ngày tải lên: 13/11/2012, 10:56

... DENEXCH to Windows NT 4.0 Service Pack 4, and then upgrade to Windows 2000 Server Upgrade all Windows NT Workstation 4.0 computers to Windows NT 4.0 Service Pack 4, and then upgrade to Windows 2000 ... back to Windows NT B: NTDSutil is used for restoring Active Directory objects It cannot be used to restore the system back to Windows NT C: DCPro...

Ngày tải lên: 18/10/2013, 17:15

... no ip directed-broadcast encapsulation frame- relay clockrate 56000 cdp enable frame- relay intf-type dce frame- relay route 17 interface Serial0/2 16 frame- relay route 18 interface Serial0/1 16 ... Use show frame- relay pvc and show frame- relay map to troubleshoot connectivity problems Rebooting the Frame Relay switch might also solve connectivity issues SanJose3#show...

Ngày tải lên: 19/10/2013, 03:15

... context-sensitive help for more information Migrating from NetWare 3.x to NetWare If you have a NetWare 3.x server you want to upgrade to NetWare 6, you will need to purchase a new server box Generally, ... Preparing the Server Hardware Before installing or upgrading to NetWare 6, you should make sure that you have a properly configured server to run NetWare Sy...

Ngày tải lên: 26/10/2013, 23:15

... subject to future change Transferability of Web Easy to transfer to GPFR Total re-write to transfer Very easy to transfer Services API to to XML-RPC Extension or XML-RPC Extension Total re-write to ... going to have to start looking for something to with all the time I’m going to save! php| a Have you had your PHP today? Visit us at http://www.phparch.com and subscr...

Ngày tải lên: 11/12/2013, 02:15

... 10 .10 .11 .1 10 .10 .11 .1 10 .10 .11 .2 10 .10 .11 .1 10 .10 .12 .2 10 .10 .11 .1 10 .10 .13 .2 10 .10 .11 .1 172 .19 .1. 4 10 .10 .11 .1 192 .16 8 .1. 0 10 .10 .11 .1 192 .16 8 .10 .1 10 .10 .11 .1 r1# sh ip ospf neigh Neighbor ID 19 2 .16 8 .10 .1 ... 0x800000 01 0x8E 41 Summary Net Link States (Area 1) Link ID 10 .10 .11 .1 10 .10 .11 .2 10 .10 .12 .2 10 .10 .13...

Ngày tải lên: 11/12/2013, 14:15

... 注意前面的 P 代表 passive 状态,这样的状态是正常的如果看见的是 A 即 active 状态而不是 P,说明 router 失去了到这个网络的路径并且在寻找替代路径 Open Shortest Path First(OSPF) Basics 在 个大型网络中,假如不是所有的设备都是 Cisco 的,EIGRP 明显就不行,因为它是私有的 所以就可以使用 OSPF 协议或者路由 ... 14.point-to-multipoint:点对多点网络.不需要 DR 和 BDR SPF Tree Calculation 在 个区域内,每个 r...

Ngày tải lên: 21/12/2013, 05:17

... substations (LTCs, regulators and capacitor banks) using adaptive strategies • Storm Mode Fuse-saving/blowing logic - Use input from SCADA (storm, no storm) to change fuse-blowing logic to improve SAIDI/SAIFI ... Protection and Process Automation, Maintenance Automation, Information Automation, and Information Distribution Some examples of applications are: • Advanced Breaker Monit...

Ngày tải lên: 22/12/2013, 21:18

... Chapter 8: Migrating Content from Earlier Drupal Versions 109 Chapter 9: Migrating from WordPress 1 27 Upgrading Drupal to Upgrade Status and Upgrade Assist Upgrading Drupal core Migrating Drupal ... Migrating to Drupal Learn how to quickly and efficiently migrate content into Drupal from a variety of sources including Drupal using automated migration and import ....

Ngày tải lên: 16/03/2014, 03:20

... Director Server on Windows and migrating to a Microsoft SQL Server database Upgrading and migrating IBM Systems Director Server You can upgrade IBM Systems Director Server to version 6. 3 and migrate ... complete a post-installation configuration on IBM Systems Director Server 6. 3. 2 to switch your non-default database...

Ngày tải lên: 31/03/2014, 16:20