Automotive mechanics (volume i)(part 6, chapter37) basic electronics

... 001-016_May_chap 01 12/9/06 9:38 AM Page 3 Chapter Motor vehicle components Mechanical arrangements Sections of a motor vehicle The engine assembly Vehicle construction The drive train Transmissions ... enable various components which make up the mechanical section of a motor vehicle to be identified ■ The terms components, parts, units and items are all used in relation to...

Ngày tải lên: 14/02/2017, 14:57

... mechanical items Body repairs are usually carried out in a separate body repair workshop Automotive service procedures All automotive service jobs have certain procedures Procedures are ways of doing ... engine, transmission, body and so on An automotive mechanic must be able to refer to workshop manuals and interpret the information that they contain Workshop manuals have a conte...

Ngày tải lên: 14/02/2017, 15:02

... chapter three tools and their use Ring and open-end spanners are a combination, with a ring at one end and open jaws at the other The ring end can be used for loosening a bolt or nut and for final ... of a hand lever Tools for threading In the workshop, threads are cut by taps and dies A set of tools consists of a stock and dies and also a tap wrench and taps (Figure...

Ngày tải lên: 14/02/2017, 15:05

... Page 57 chapter four measuring and checking it until the anvil and the spindle are both lightly in contact with the cylinder walls Move the micrometer up and down slightly and also from side to ... 9:43 AM Page 59 chapter four measuring and checking figure 4.13 Sleeve and thimble markings on an inch micrometer To understand the scales, read the main scale first and then...

Ngày tải lên: 14/02/2017, 16:00

... and roller-type bearings, and by special antifriction metals in many plain bearings Application of friction to bearings An appreciation of friction and how it applies in actual bearings is helpful ... chapter five friction and bearings Technical terms Friction, static friction, sliding friction, rolling friction, fluid friction, surface-finish, traction, adhesion,...

Ngày tải lên: 14/02/2017, 16:02

... chapter six seals, gaskets and sealants 95 Oil pan gaskets Manifold gaskets Some oil pans and other parts are made as steel pressings These are not as rigid as cast parts and so require gaskets that ... assembly Handling and storing gaskets Gaskets should be handled and stored carefully to prevent damage which could render the gasket useless Some points to be observed...

Ngày tải lên: 14/02/2017, 16:04

... automatic In a workshop, people have to consider the safety of others as well their own They must understand general workshop safety requirements and, in particular, the need for safety when operating ... or be dropped Safety footwear is designed with reinforced toecaps to provide protection against these types of accidents ■ Open or soft footwear should not be worn in the worksho...

Ngày tải lên: 14/02/2017, 16:06

... accessories Fittings 99 Examples of pneumatic applications 65 52 Handling 4 b a Pick-and-place units a) Twin-axis pick-and-place unit b) Three-axis handling device with a hexapod design Guide rod Guide ... cup VAS or gripper HG 66 99 Examples of pneumatic applications Rodless linear unit DGP or Positioning axis DGE with multi-axis positioning Mounting controller MPS 53 Handling A B 10...

Ngày tải lên: 08/08/2014, 11:21

... vd Prof C.K Tse: Diode circuits 13 Basic load line construction + vR – iR i R :) Vs + _ id + vd – slope = –1/R id device characteristic nonlinear device vd Prof C.K Tse: Diode circuits v Vs 14 ... — 50 V Better — 50 – 1.4 = 48.6 V Prof C.K Tse: Diode circuits Application examples clamper dc restorer half-wave doubler Prof C.K Tse: Diode circuits full-wave doubler A nonlinear...

Ngày tải lên: 13/12/2013, 22:15

... Basic Electronics & Theory Lesson 5. 5 Series & Parallel Resistors Series circuits R = R1 + R2 + R3 + R1=100 ohms R2= 150 ohms R3=370 ohms RT= 620 ohms 32 Basic Electronics & Theory Lesson 5. 5 ... V, so: I1 = 10 / = 1. 25 A I2 = 10 / = 1. 25 A I3=10 / = 2 .5 A Note that the currents add together to 5A, the total current 34 Basic Electronics & Theory Les...

Ngày tải lên: 28/04/2014, 14:25

... switching losses and efficiently design the output EMI filter 2 06 New Trends and Developments in Automotive System Engineering References Chang, C & Knights, Mike A (1995) Interleaving technique in ... 208 New Trends and Developments in Automotive System Engineering Fig Hot spot as it appears on a clutch desk 1.1 Automotive brake and clutch system...

Ngày tải lên: 20/06/2014, 07:20

... of Centre for Electronics Design and Technology of India A Scientific Society of Department of Electronics, Govt of India, New Delhi First Edition: 1999 TRADE MARKS: All brand name and product ... state governments, industry and department of electronics CEDTI is a quality conscious organisation and has taken steps to formally get recognition of the quality and standards in var...

Ngày tải lên: 03/07/2014, 21:13

... 0WODGT BASIC ELECTRONIC COMPONENTS & HARDWARE-II 016'5 11 BASIC ELECTRONIC COMPONENTS & HARDWARE-II 016'5 12 BASIC ELECTRONIC COMPONENTS & HARDWARE-II 016'5 13 BASIC ELECTRONIC COMPONENTS & HARDWARE-II ... FGVCKN 27 BASIC ELECTRONIC COMPONENTS & HARDWARE-II 016'5 28 BASIC ELECTRONIC COMPONENTS & HARDWARE-II 016'5 29 BASIC ELECTRONIC COMPONENTS & HARD...

Ngày tải lên: 03/07/2014, 21:13