Automotive mechanics (volume i)(part 2, chapter10) cooling systems and service

... chapter three tools and their use Ring and open-end spanners are a combination, with a ring at one end and open jaws at the other The ring end can be used for loosening a bolt or nut and for final ... of a hand lever Tools for threading In the workshop, threads are cut by taps and dies A set of tools consists of a stock and dies and also a tap wrench and taps (Figure...

Ngày tải lên: 14/02/2017, 15:05

... Page 57 chapter four measuring and checking it until the anvil and the spindle are both lightly in contact with the cylinder walls Move the micrometer up and down slightly and also from side to ... 9:43 AM Page 59 chapter four measuring and checking figure 4.13 Sleeve and thimble markings on an inch micrometer To understand the scales, read the main scale first and then...

Ngày tải lên: 14/02/2017, 16:00

... and roller-type bearings, and by special antifriction metals in many plain bearings Application of friction to bearings An appreciation of friction and how it applies in actual bearings is helpful ... chapter five friction and bearings Technical terms Friction, static friction, sliding friction, rolling friction, fluid friction, surface-finish, traction, adhesion,...

Ngày tải lên: 14/02/2017, 16:02

... 001-016_May_chap 01 12/9/06 9:38 AM Page 3 Chapter Motor vehicle components Mechanical arrangements Sections of a motor vehicle The engine assembly Vehicle construction The drive train Transmissions ... enable various components which make up the mechanical section of a motor vehicle to be identified ■ The terms components, parts, units and items are all used in relation to...

Ngày tải lên: 14/02/2017, 14:57

... mechanical items Body repairs are usually carried out in a separate body repair workshop Automotive service procedures All automotive service jobs have certain procedures Procedures are ways of doing ... engine, transmission, body and so on An automotive mechanic must be able to refer to workshop manuals and interpret the information that they contain Workshop manuals have a conte...

Ngày tải lên: 14/02/2017, 15:02

... chapter six seals, gaskets and sealants 95 Oil pan gaskets Manifold gaskets Some oil pans and other parts are made as steel pressings These are not as rigid as cast parts and so require gaskets that ... assembly Handling and storing gaskets Gaskets should be handled and stored carefully to prevent damage which could render the gasket useless Some points to be observed...

Ngày tải lên: 14/02/2017, 16:04

... automatic In a workshop, people have to consider the safety of others as well their own They must understand general workshop safety requirements and, in particular, the need for safety when operating ... or be dropped Safety footwear is designed with reinforced toecaps to provide protection against these types of accidents ■ Open or soft footwear should not be worn in the worksho...

Ngày tải lên: 14/02/2017, 16:06

... candidate business objects Review candidate business objects for possible redundancy or lack of applicability Activity 5.2: Identifying Business Objects and Services Exercise 2: Identifying Services ... 30 Activity 5.2: Identifying Business Objects and Services Exercise 1: Identifying Business Objects (15 min) ! Identify candidate business obje...

Ngày tải lên: 10/12/2013, 16:16

... (58), (67) and (68), for given S1 and S , one can drive the maximum cooling load and corresponding COP of the irreversible quantum Carnot refrigerator with heat resistance and heat leakage analytically ... performance of harmonic and spin-1/2 quantum refrigeration cycles, many authors studied the performance of quantum refrigerator using ideal quantum Bose a...

Ngày tải lên: 05/09/2013, 15:28

... 2011 IBM Corporation Than More Informationk you! 44 © 2011 IBM Corporation on ibm. com • IBM CloudBurst on x http://www-03 .ibm. com /systems/ x/ solutions/infrastructure /cloud/ index.html • IBM CloudBurst ... availability of Cloud Management Platform • SVC • Appliances: – IBM WebSphere CloudBurst – IBM WebSphere DataPower Cast Iron (hybrid cloud) • Capacity pl...

Ngày tải lên: 23/03/2014, 08:20

... from
the
null
hypothesis
(that
residents
of
 
 all
 three
 streets
 would
 have
 similar
 21
 
 





















 World Transport Policy and Practice 
 Volume 17.2 June 2011 
 
 
 numbers
 ... University
 Sustainability
 Policy (CUSP)
Institute
 Perth,
Western
Australia
 
 Email:
kenworthy@em.uni‐frankfurt.de
 
 World Transport Policy and Practice 
 Volume 17.2 June 2011 
 
 Referenc...

Ngày tải lên: 23/03/2014, 10:20

... 15 20 20 0 21 360 Using the Ord er of Operati Simplify ons p 69 22 12, 36, or 108 23 8, - × (6 24 14, -14 25 = 11 6) 11,4 × (0) 26 20 , -20 27 28 -1 29 - 12 30 =31 • Simplify (16) - × 32 33 35 34 ... decimal places ( 62. 43) Rounding 62. 428 12 to two decimal places ( 62. 43) is more accurate than rounding 62. 428 12 to one decimal place ( 62. 4) Rounding 62. 428 12 to one de...

Ngày tải lên: 27/03/2014, 11:59