american petroleum institute api 2510 design and construction of lpg installations

... Design and Construction of LPG Installations Downstream Segment API STANDARD 2510 EIGHTH EDITION, MAY 2001 American Petroleum Institute Helping You Get The Job Done Right~M SPECIAL NOTES API ... FITTINGS, AND OPTIONAL EQUIPMEN 21 Minimum Horizontal Distance Between Shell of Pressurized LPG Tank and Line of Adjoining Property That May Be Developed Design and...

Ngày tải lên: 27/03/2014, 14:08

... Copy, © BSI BS 5588- 4: 1978 Figure — Steps in obtaining the equivalent resistance of a combination of series and parallel paths of air leakage 12 © BSI 01-1999 BS 5588- 4: 1978 For combinations of series ... and construction of buildings BS 5588- 1, Residential buildings BS 5588- 1.1, Code of practice for single-family dwelling houses3) BS 5588-...

Ngày tải lên: 28/09/2014, 23:27

... Copy, © BSI BS 5588- 4: 1978 Figure — Steps in obtaining the equivalent resistance of a combination of series and parallel paths of air leakage 12 © BSI 01-1999 BS 5588- 4: 1978 For combinations of series ... Copy, © BSI Foreword This new code of practice was prepared under the direction of the Fire Standards Committee In addition to the existing BS...

Ngày tải lên: 28/09/2014, 23:27

... affect the extent of firefighting shafts and of the firefighting lifts and stairs in them The minimum extent of firefighting lifts and stairs is shown in Figure In tall buildings and buildings ... Use of this code Section Planning and construction Firefighting shafts Firefighting stairs 14 Firefighting lobbies 14 Fire mains and landing valve...

Ngày tải lên: 28/09/2014, 23:28

... Concrete Institute 307-69 Specification for the Design and Construction of Reinforced Concrete Chimneys 307-88 Standard Practice for the Design and Construction of Cast-in-Place Reinforced Concrete ... Concrete Chimneys 318 Building Code Requirements for Structural Concrete 505-54 Standard Specification for the Design and Construction of Reinforced...

Ngày tải lên: 24/10/2014, 15:45

... determined by test and the values shown used with caution See Commentary on Section 4.4.1 COMMENTARY ON DESIGN AND CONSTRUCTION OF CONCRETE SILOS AND STACKING TUBES 313R-9 Fig 4-D—Flow chart for selecting ... for computing these bending moments COMMENTARY ON DESIGN AND CONSTRUCTION OF CONCRETE SILOS AND STACKING TUBES 313R-17 Fig 7-A For...

Ngày tải lên: 24/10/2014, 15:45

... including the design strength of the concrete, the thickness of the concrete chimney shell, the size and position of reinforcing steel, details and dimensions of the chimney lining, and information ... CHAPTER 3 CONSTRUCTION REQUIREMENTS 3.1—General Concrete quality, methods of determining strength of concrete, field tests, concrete proportions and consistency,...

Ngày tải lên: 24/10/2014, 15:46

... B.7—Support uniformity Uniformity of support for a concrete pavement is key to its longevity Only the most often-used methods for achieving GUIDE FOR DESIGN AND CONSTRUCTION OF CONCRETE PARKING LOTS 330R-27 ... Joints on Performance and Design of GUIDE FOR DESIGN AND CONSTRUCTION OF CONCRETE PARKING LOTS Plain Concrete Pavement,” Highway Res...

Ngày tải lên: 24/10/2014, 15:47

... silos and stacking tubes for storing granular materials Silos for storing of ensilage have different requirements and are not included However, industrial stave silos for storage of granular materials ... ACI STANDARD Standard Methods of Sampling and Testing Concrete Masonry Units Standard Specification for Portland Cement Standard Specificati...

Ngày tải lên: 24/10/2014, 16:04

... 1.2—Objective The objective of this report is to provide guidance in the design and construction of circular prestressed concrete structures circumferentially prestressed using tendons 1.3—Scope The ... facilitate placement of the concrete without segregation (a) 10 in for cast-in-place concrete walls with internal circumferential tendons, with or without ve...

Ngày tải lên: 24/10/2014, 17:26

... reinforced concrete and prestressed concrete design and construction given in ACI 318-99, ACI 350-01, and ACI 301 Design and construction recommendations cover the following elements or components of circularwrapped ... from the restraint of deflections, rotations, and deformations that DESIGN AND CONSTRUCTION OF PRESTRESSED CONCRETE STRUCTURES 372R-7...

Ngày tải lên: 24/10/2014, 17:26

... out -of- plumb construction and foundation tilt GUIDE FOR CONCRETE-PEDESTAL WATER TOWERS The combination of these effects is random, and the deviations implied by Eq (4-1a) should not be used as construction ... moment at the base to the top of the structure as required by ASCE for inverted pendulum structures For ease of calculation, the top of the...

Ngày tải lên: 24/10/2014, 17:26

... design details B.11- Other factors PREFACE Concrete structures have been used in the North Sea and other offshore areas of the world With the rapid expansion of knowledge of the behavior of concrete ... indicated for consideration by the designer The design of offshore structures requires much creativity of the designer, and it is intended that...

Ngày tải lên: 24/10/2014, 17:40

... Reese, L C., Handbook for Design of Piles and Drilled Shafts Under Lateral Load, U.S Dept of Trans., Federal Terzaghi, K., “Evaluation of the Modulus of Subgrade Highway Admin., Office of Implementation, ... contamination, influence the choice of construction method and thus the design The effects of the design and the 336.3R-5 construction methods used for new...

Ngày tải lên: 24/10/2014, 21:58