Contactor for motor schneider
... Taper Rotor Loại vành ngắn mạch Brake Motor Không Không ñồng ñồng bộ rôto rôto dây dây quấn quấn Công suất nhỏ ðộng vạn Mômen lớn ðộng ñặc biệt Repulsion Motor Eddy Current mottor STU HCM City ... vệ S/C 0.01 10 13 xIn STU HCM City 19 sản phẩm vs sản phẩm GV2ME16 GV2L16 LC1D12 LC1D12 LRD16 Motor Motor 30% rẻ ẻ STU HCM City 20 Tùy chọn: Ghép nối áp-tô-mát công-tắc-tơ Option: GV2-AF ñơn g...
Ngày tải lên: 21/05/2016, 18:21
... 166 22 PRIME MOVERS FOR MOTOR VEHICLES TABLE 22.1 Onboard energy storage Energy density e/m, power density P/m and general characteristics (data for electrochemical energy ... was the introduction of rotary internal combustion engines Some vehicles with this innovative engine 168 22 PRIME MOVERS FOR MOTOR VEHICLES were mass produced and had a limited commercial success...
Ngày tải lên: 03/07/2014, 19:20
Ngày tải lên: 27/03/2015, 13:54
AN0898 determining MOSFET driver needs for motor drive applications
... Gate Driver Circuitry: PDRIVER = CGATE * V GATE2 * F Where: F = Switching Frequency 2003 Microchip Technology Inc DS00898A-page 11 AN898 DETERMINING THE MOSFET DRIVER RATING FOR THE GATE DRIVE ... diagram for a MOSFET driver is shown in Figure 18 MOSFETs Q1 and Q2 represent the pull-up and pull-down output drive stage of the MOSFET driver A common misconception about...
Ngày tải lên: 11/01/2016, 14:35
Tài liệu A neural-network-based space-vector PWM controller for a three-level voltage-fed inverter induction motor drive doc
... signals are compared with the output of a single UP/DOWN counter and processed through a logic block to generate the PWM outputs for for for for for (5) for for for for for for for for for for ... -phase P states and performed with the and signals only Similar operations are signals of all the phases and all the The drive performance was evaluated in detail by simulati...
Ngày tải lên: 22/12/2013, 08:16
A park like transformation for the study and the control of a nonsinusoidal brushless DC motor
... therefore in this paper a new transformation which preserves the same advantages as the Park transformation A Mathematical Model of the BDCM We suppose that the motor has the following typical features ... pulsating torque (the homopolar part) and a two-phase motor with a rotating field (the "ap" The classical Park transformation is, in fact, the succ...
Ngày tải lên: 03/01/2014, 19:44
Pseudo vector control – an alternative approach for brushless DC motor drives
... improve the performance of the Brushless DC Motor drives The vector- control principle in dq synchronously rotating frame is utilized for the generation of current references only, and the motor currents ... proposed Pseudo- vector Control for BLDCM drives III PRINCIPLE OF PSEUDO- VECTOR CONTROL In the conventional square-wave phase current control (Fig 2), for...
Ngày tải lên: 03/01/2014, 19:46
Research on field weakening based on reactive power with BLDC motor for electric vehicle application
... FIELD - WEAKENING BASED ON REACTIVE POWER WITH BLDC MOTOR The electrical machinery power is composed by the active power and the reactive power[ 9]-[10] In the static α − β frame, the active power ... control with permanent over speed area The principle of stator control based on reactive power theory for BLDC motor is described by formula A Chart of...
Ngày tải lên: 03/01/2014, 19:47
Tài liệu Guidelines for Employers to Reduce Motor Vehicle Crashes docx
... representatives to obtain the numbers you'll need Costs of Motor Vehicle Crashes to Employers Worksheet Use the worksheet found at the end of this booklet to estimate the cost of a motor vehicle crash to ... a worksheet, Costs of Motor Vehicle Crashes to Employers 27 Aggressive Driving As traffic congestion continues to grow, motorists commuting to and from w...
Ngày tải lên: 19/02/2014, 04:20
REQUIREMENTS FOR MANUFACTURERS OF MOTOR VEHICLES AND MOTOR VEHICLE EQUIPMENT ppt
... 5 Requirements for Manufacturers of Motor Vehicles and Motor Vehicle Equipment Items Disclaimer – This document is a simplified description of the requirements for manufacturers of motor vehicles ... minimum performance requirements for new motor vehicles and for certain items of motor vehicle equipment Such standards must be practicable,...
Ngày tải lên: 07/03/2014, 11:20
Expansion of Operating Limits for Permanent Magnet Motor by Current Vector Control
... cases, the permanent magnet is demagnetized irreversibly by the flux-weakening control VI DEMAGNETIZATION OF PERMANENT MAGNET If the PM motor is controlled by the foregoing fluxweakening control ... MORIMOTO et al.: EXPANSION OF OPERATING LIMITS FOR PERMANENT MAGNET MOTOR - To examine the demagnetization of the permanent magnet due to the d-axis armat...
Ngày tải lên: 08/03/2014, 22:01
Motor vehicle repair Good practice for SMART sprayers docx
... isocyanatebased products (including waterbased isocyanate products) may cause asthma and dermatitis; Motor vehicle repair: Good practice for SMART sprayers of 10 pages Health and Safety Executive ❋ UVcurable products may cause dermatitis – and may contain isocyanate; ... Suppliers of RPE for spraying will provide equipment that meets the LDH3 or LDM2 specification. Motor vehicle repai...
Ngày tải lên: 16/03/2014, 12:20
Direct control methods for matrix converter and induction motor
... Mains Start controller V CONCLUSION Modern direct control methods for matrix converters are presented The basic ideas of DTC, sliding mode control and DCC for matrix converter and induction machine ... are omitted here and can be found in [11] C Direct Current Control (DCC) In [15] and [6] a DCC method for matrix converters is presented It is based on the a...
Ngày tải lên: 13/05/2014, 00:55
DC motor control for robot
... Motor control questions Why we need speed control? How is DC motor speed controlled? How is motor direction controlled? What circuits can be used? Reasons for accurate speed control Motor ... 74HC86 Motor control diagram PROCESSOR H-BRIDGE CIRCUIT DC MOTOR ENCODER Control systems What is a control system? What are some examples? What are the types of control sys...
Ngày tải lên: 22/05/2014, 18:05