PETROLEUM DEVELOPMENT GEOLOGY RESERVOIR ENGINEERING

Ngày tải lên: 02/04/2014, 16:03

Ngày tải lên: 02/04/2014, 16:05

... of modern bioreaction engineering Bioreaction engineering is practised mainly by chemical engineers, because chemical reaction engineering is one of its platforms [11] The first biochemical engineering ... [306] 59 Development of Bioreaction Engineering distribution of metabolic flux in the cells Recent results on metabolic engineering are reported in a special iss...

Ngày tải lên: 23/10/2013, 17:20

... Development of Waterflooding During Waterflooding 46 1.2 Relation Between Reservoir Engineering and Production Engineering Aspects of Waterflooding 4.3 Ranges of Mobility Ratios 1.3 Objectives of the ... Affecting Selection of Waterftood Pattern 58 2.6 Methods of Measuring Water-Oil Flow Properties 22 Reservoir Heterogeneity 2.7 Three-Phase Relative Permeabilities...

Ngày tải lên: 02/04/2014, 16:07

... NANOSENSORS AS RESERVOIR ENGINEERING TOOLS TO MAP INSITU TEMPERATURE DISTRIBUTIONS IN GEOTHERMAL RESERVOIRS By Morgan Ames June 2011 Stanford Geothermal Program Interdisciplinary Research in ... project was to develop functional nanosensors capable of mapping the temperature and pressure distributions in geothermal reservoirs Measuring temperature...

Ngày tải lên: 28/06/2014, 22:20

... 173-178 6- 12 41.4-55 .2 3-10 1.4 -2. 8 55-60 12- 16 1 .27 1.34 1 .25 27 .6-41.4 3-10 1.4 -2. 8 60-65 >24 1 .24 55 .2- 82. 7 5-10 2. 8-4 .2 PGA 185 -22 5 25 -65 6- 12 1.53 >68.9 15 -20 >6.9 PCL 58-68 - 70 >24 1.11 20 .7-34.5 ... rates of all such polymers, the structural stability of PCL permits the study of fabrication and characterization as a tissue engineering scaffold...

Ngày tải lên: 14/09/2015, 10:20

... 64. 3 51500 1.6 55.3 39. 64 PCL-PEG Raw 63.5 33000 1.6 62 44 .44 PCL-PEG Scaffold 65.3 33600 1.7 61.8 44 .30 PCL-PEG-PCL Raw 64. 4 30000 1.8 48 34. 41 PCL-PEG-PCL Scaffold 65.6 31700 1.7 47 .2 33. 84 ... (bar) Figure 4. 11: Influence of extrusion pressure on RW and porosity of the scaffolds fabricated with lay-down pattern of 0/90 and nozzle size of 500 µm 113 Chapter Fou...

Ngày tải lên: 14/09/2015, 10:23

... Chapter Five: Conclusions and Recommendations 5. 1 Conclusions A desktop robot based rapid prototyping (DRBRP) melt extrusion system was designed and developed in house ... filament diameter and consequently, the pore size and porosity A range of filament diameter (3 75 to 623 µm) and porosity ( 45 to 75% ) was obtained by varying the process parameters In spite of...

Ngày tải lên: 14/09/2015, 10:23

... accuracy of up to 2°C and the feed rate had the deposition speed accuracy of up to 3mm/min Material Loading Port Teflon Insulator Figure 3. 2: Four-axes desktop robot-based rapid prototyping system 3. 4.2 ... (0/90°, 0/60/120° and 0 /30 /60/90/120/150°) as shown in Figure 3. 4 using appropriate positioning of the robotic control system The lay-down patterns of 0/90°, 0/60...

Ngày tải lên: 14/09/2015, 11:12