Inkjet printing of conjugated polymer fullerene solar cell films

... Introduction .104  5.2 Inkjet printing of P3HT:PCBM solar cell films 106  5.3 Dynamic drying of inkjet printed P3HT:PCBM films .109  5.4 Inkjet printed P3HT:PCBM OPV performance ... integrated into the printing technology Figure 1-6: Printing technology (a) Flexographic printing (b) Gravure printing (c) Offset printing (d) Inkjet printing (e) Screen printing...

Ngày tải lên: 09/09/2015, 10:08

... doi:10.1186/1556-276X-6-83 Cite this article as: Hu et al.: Improvement of performance of InAs quantum dot solar cell by inserting thin AlAs layers Nanoscale Research Letters 2011 6:83 Submit your ... GaInP/GaInAs/Ge multijunction solar cells Appl Phys Lett 2007, 90:183516 McPheeters CO, Hill CJ, Lim SH, Derkacs D, Ting DZ, Yu ET: Improved performance of In(Ga)...

Ngày tải lên: 21/06/2014, 06:20

... Characterisation of surface passivation 10 2.4 Technological methods to improve surface passivation 15 2.5 Surface passivation for high-efficiency c-Si solar cells 25 2.6 Fabrication of test ... used for industrial screen-printed silicon solar cells Development of cheaper, improved and alternative process technologies for surface passivation of moderately a...

Ngày tải lên: 09/09/2015, 11:08

... Because of this reason, the film with 3.5 vol.% of 1,8-octanedithiol exhibited the best device performances in this work Conclusions The performance characteristics of BHJ polymer solar cells based ... doi:10.1186/1556-276X-7-56 Cite this article as: Kim et al.: Performance characteristics of polymer photovoltaic solar cells with an additive-incorporated a...

Ngày tải lên: 20/06/2014, 23:20

... Because of this reason, the film with 3.5 vol.% of 1,8-octanedithiol exhibited the best device performances in this work Conclusions The performance characteristics of BHJ polymer solar cells based ... doi:10.1186/1556-276X-7-56 Cite this article as: Kim et al.: Performance characteristics of polymer photovoltaic solar cells with an additive-incorporated a...

Ngày tải lên: 21/06/2014, 17:20

... calibrated using a standard solar cell composed of a crystalline silicon solar cell and an infrared cutoff filter (KG-5, Schott AG, Mainz, Germany) Raman spectra were obtained on a Senterra R200-L ... Reduction of graphene oxide by an in- situ photoelectrochemical method in a dye-sensitized solar cell assembly Chen Chen1, Mingce Long*1, Min Xia1,...

Ngày tải lên: 21/06/2014, 17:20

... the solar cell performance as compared to solar cell w/SLAR structure To investigate the performance of silicon nitride SWS before fabricating on a real silicon solar cell, we simulated the solar ... efficiency of 0.8% can be seen for silicon solar cell with silicon nitride SWS over a cell with single layer silicon nitride ARCs and only 0.3% less in e...

Ngày tải lên: 22/06/2014, 00:20

... deposition of different thicknesses of CHLO thin films on the PT thin films is also successfully done by spin coating technique The electrical conductivity in dark condition was increased with the ... increasing of PT thin film thickness While, with the increasing of CHLO thin film thickness, electrical conductivity in the dark is consecutively change Under dark...

Ngày tải lên: 07/08/2014, 14:20

... Department of Biological Sciences iii ABSTRACT This dissertation explores the synthesis, characterization, and application of conjugated polymers as fluorescence turn-on chemosensors A series of conjugated ... Experimental Section 34 2.3 Results and Discussion 40 2.3.1 40 Synthesis and Characterization xi Sonogashira coupling 40 Synthesis of monomers 43 Synthesis...

Ngày tải lên: 13/11/2014, 10:54

... categories of inkjet printing technology: Continuous inkjet printing and Drop- on- Demand inkjet printing 10 of 176 Chapter 2: Literature Review Fig 2.1: Layout of the different inkjet printing technologies ... resolution printing Another ongoing measurement of the resolution of inkjet printing is to use drop pitch in favor of metrication Drop...

Ngày tải lên: 11/09/2015, 09:56

... Inkjet Printing Drop Ejection Parameters A.1 VI Summary SUMMARY This thesis aims to further investigate the application of drop- on- demand (DoD) inkjet printing technology in the fabrication of ... Discussion 118 4.3.1 ITO Surface Patterning 118 4.3.2 Drop- on- Demand Inkjet Printing of PEDOT:PSS 119 4.3.3 Characterization of P-OLED Devices 127 4.4 Conclus...

Ngày tải lên: 11/09/2015, 10:17

... DROP- ON- DEMAND INKJET PRINTING TECHNOLOGY WITH APPLICATIONS TO POLYMER LIGHT- EMITTING DIODES NG YUAN SONG (B.Eng (Hons.)), NUS A THESIS SUBMITTED FOR THE ... Drop- on- Demand modes of operation Inkjet Printing Technology Binary Deflection Continuous Inkjet Printing (C-IJP) Drop- on- Demand Inkjet Printing (DoD-IJP) Multiple Deflection Microdot T...

Ngày tải lên: 04/10/2015, 17:04

... persistently HBV expressing cell line HepG2.215 and its parent cell line, a non-HBV expressing cell line HepG2 We found that cIAP1 and cIAP2 were clearly increased in the HBV expressing cells but XIAP ... expression in the HBV expressing cells was first investigated by the comparison of the gene expression profile in the HepG2.215 and HepG2 cells using gene arra...

Ngày tải lên: 02/11/2012, 11:17

... 800 800 900 900 Reflectivity (% ) Internal quantum efficiency (% ) 100 100 0 1000 1000 Wavelength (nm) Wavelength (nm) [3] D.C Johnson et al Solar Energy Materials and Solar Cells, 2005 Giải thích ... Nguyên lí Chế tạo Ưu Ứng dụng Nguyên lí • • • • Cấu trúc giếng lượng tử (QW) Nguyên liệu chế tạo QW Phân loại QW Hố lượng tử GaAs/GaAsAl outline • • • • • • History-lịch...

Ngày tải lên: 06/12/2012, 08:28