Process industrial instruments and controls handbook
The Control Techniques Drives and Controls Handbook
... Performance and applications Direct torque control D.C motor drive control Flux controller Torque controller Performance and applications Analysis of and set up of a speed controller Ideal speed controller ... 101 Drive control 103 General The ideal control system Open-loop control Closed-loop control Criteria for assessing the performance of a closed-loop control syst...
Ngày tải lên: 20/10/2013, 02:15
Tài liệu Industrial Power Engineering and Applications Handbook P2 docx
... system KOA1 (Courtesy: NGEF Ltd) Totally dust-tight No ingress of dust 1/24 Industrial Power Engineering and Applications Handbook Table 1.11 Types of Protection against ingress of water For gases ... numeral is used for circulation by any means other than stated above 1/26 Industrial Power Engineering and Applications Handbook Figure 1.20(a) Totally enclosed tube ven...
Ngày tải lên: 19/01/2014, 23:20
Tài liệu Industrial Power Engineering and Applications Handbook P1 docx
... NEWNES POWER ENGINEERING SERIES Industrial Power Engineering and Applications Handbook NEWNES POWER ENGINEERING SERIES Series editors Professor TJE Miller, ... Relunctance Machines 7506 5073 NEWNES POWER ENGINEERING SERIES Industrial Power Engineering and Applications Handbook K.C Agrawal Newnes BOSTON OXFORD AUCKLAND JOHANNESBURG MELBOURNE NEW DELHI ... Li...
Ngày tải lên: 19/01/2014, 23:20
Xe ô tô BMW X5 E70 SM 06a_E70 Displays Indicators and Controls
... the E70 • Identify the changes to the Displays, Indicators and Controls on the new BMW X5 E70 Displays, Indicators and Controls Introduction Displays, Indicators and Controls As in all other BMW ... identical and are described in detail in the BMW X5 Owner's Handbook This product information only outlines the changes compared to the BMW Series and BMW...
Ngày tải lên: 19/10/2012, 13:50
English for industrial machinery and equipment(Tiếng anh chuyên ngành máy móc và thiết bị
... paper The paper is formed in vertical convolutions (wrinkles) and in a cylindrical pattern It is reinforced on the inside and outside and is equipped with a seal on the top and the bottom Sometimes ... location and movement Indefinite and definite articles Expressing design and function 18 UNIT 4: ENERGY, HEAT AND WORK A UNDERSTANDING A PRINTED TEXT The following text will giv...
Ngày tải lên: 01/03/2013, 17:01
Process technology equipment and systems chapter 1 & 2
... Problems and Solutions 20 8 Cooling Tower Symbols 21 0 Summary 21 1 Review Questions 21 2 Chapter Boilers 21 3 Key Terms 21 4 Boiler Applications and Basic ... 2 21 Steam Generation System 22 3 Steam System Symbols 22 5 Summary 22 6 Review Questions 22 7 Chapter 10 Furnaces 22 9 Key Terms 23 0 Furnace ... 21 5 Fire-Tube Boilers 21 5 Water-Tube Boilers 21 5 Main Componen...
Ngày tải lên: 15/08/2013, 07:50
Process technology equipment and systems chapter 3 & 4
... 43 . 77 49 .56 53. 52 65 .42 73. 15 88. 63 107 .32 125 .49 139 .67 160.27 52.65 52.25 51.07 49 . 74 49.00 48 .50 46 .92 46 .00 44 . 04 41.66 39 .33 37 .52 34 .89 3. 338 3. 338 3. 338 3. 338 3. 338 3. 338 3. 338 3. 338 3. 338 ... 0 83 120 237 33 7 43 8 531 6 74 4 .33 4 4.260 4. 026 3. 826 3. 6 24 3. 43 8 3. 152 1.152 1.651 3. 1 74 4 .40 7 5.595 6.621 8.101 14....
Ngày tải lên: 16/08/2013, 15:29
Process technology equipment and systems chapter 5 & 6
... Shutdown, and Troubleshooting of Compressor Systems Tables 5. 1 and 5. 2 illustrate typical startup and shutdown procedures Tables 5. 3 and 5. 4 illustrate troubleshooting charts for identifying and solving ... 47.04 psia 3.2 150 .52 8 psia Stage Three 150 .52 8 psia 3.2 481 .68 9 psia Stage Four 481 .68 9 psia 3.2 154 1.407 psia The basic components of a centrifugal compresso...
Ngày tải lên: 19/08/2013, 10:47
Process technology equipment and systems chapter 7 & 8
... designed to operate in temperatures up to 300°F (1 48. 88 C), whereas plastic blades are limited to air temperatures between 160°F and 180 °F (71 .11°C, 82 .22°C) Air-cooled heat exchangers can be found ... V-202B Ti 202A Feed Tank V-202A Figure 7. 24 Heat Exchanger System 184 Pump 80 ºF Heat Exchangers and Systems side of the first exchanger at 80 °F (26.66°C) and exits the shell...
Ngày tải lên: 20/08/2013, 10:39
Process technology equipment and systems chapter 9, 10 & 11
... distillation systems, and reaction systems They can be used for such processes as laminating, vulcanizing, extrusion, firefighting, and flare systems; and to provide cooling or heating to process equipment ... Stack P AE AT 10% EXCESS AIR I o 3% AIC 100 150 140 168ºF 120 TR 100 PR 100 TAH 80 Excess Air % 60 100 385ºF PT PE PIC 100 CASC 40 -.Slight Negative 20 -.05 inch of...
Ngày tải lên: 21/08/2013, 10:47
Process technology equipment and systems chapter 12&13
... Standardized symbols and diagrams have been developed for most pieces of industrial equipment, process flows, and instrumentation 303 Chapter 12 ● Process Diagrams Review Questions Describe a process ... describe a process unit; also called piping and instrumentation drawing Types of Process Diagrams Process diagrams can be broken down into two major categories: process...
Ngày tải lên: 23/08/2013, 14:30