guide for polymer concrete overlays
guide for concrete highway bridge deck construction
... particular attention for
bridge decks are as follows:
a.
The concrete production and delivery equipment
should be reviewed at the preconstruction
plan-
CONCRETE HIGHWAY BRIDGE DECK CONSTRUCTION
345R-9
b.
c
.
d
.
e
.
TABLE ...
Reinforcement
i
BOTTOM OF SLAB
Fig. 2.4 Typical dimensions and tolerance for location of
reinforcing steel in concrete bridge decks
Fig. 2.5...
guide for consolidation of concrete
... and wall forms: Centrifu-
gal force = 0.5 [(mass of form) + 0.2 (concrete mass)].
2. For stiff mixtures in pipe and other rigid forms: Centrif-
ugal force = 1.5 [(weight of form) + 0.2 (concrete ... consolidation of concrete by permitting place-
ment with less consolidation effort. Refer to reports of ACI
Committee 226 for more information regarding these mate-
rials. The...
guide for design and construction of concrete parking lots
... areas and access
for delivery vehicles. The design and construction of concrete slabs for
parking lots and outside storage areas share many similarities with the
design and construction of streets ... Performance and Design of
GUIDE FOR DESIGN AND CONSTRUCTION OF CONCRETE PARKING LOTS 330R-21
Plain Concrete Pavement,” Highway Research Re...
guide for determining the fire (reapproved 1994) endurance of concrete elements
... the bottom of
the slab. If the underside of the slab is exposed to fire, the
bottom of the slab will expand more than the top, resulting in
a deflection of the slab. The tensile strength of the ... percent of the maximum negative mo-
ment reinforcement in the span extend throughout the span
FIRE ENDURANCE OF CONCRETE ELEMENTS 216R-7
Fire
Fir...
guide for measuring, mixing, transporting, and placing concrete
... methods of placing concrete.
304R-1 7MEASURING, MIXING, TRANSPORTING, AND PLACING CONCRETE
5.2—Planning
A basic requirement in all concrete handling is that both
quality and uniformity of the concrete, ... 304R-1 5MEASURING, MIXING, TRANSPORTING, AND PLACING CONCRETE
Fig. 5.2(a) to (d)—Correct and incorrect methods of placing concrete.
304R-16
ACI COMMIT...
guide for structural lightweight-aggregate concrete
... involvement before design.
Concrete, structural lightweight aggregate—See
concrete, structural lightweight.
Concrete, structural lightweight (SLC) Structural
lightweight-aggregate concrete made with structural ... successful use, and the performance of
structural lightweight-aggregate concrete in service.
This guide includes a definition of lightweight-aggregate con...
guide for the use of silica fume in concrete
... products,
specifications.
CONTENTS
Chapter 1—Introduction, p. 234R-2
1.1—General
1.2—What is silica fume?
1.3 Silica fume versus other forms of synthetic silica
1.4—Using silica fume in concrete
1.5—Using silica fume in blended ... is silica fume (ACI 116R).
The initial interest in the use of silica fume was mainly
caused by the strict enforcement...
guide for use of normal weight and heavyweight aggregates in concrete
... 221R-1
This guide presents information on selection and use of normal weight and
heavyweight aggregates in concrete. The selection and use of aggregates in
concrete should be based ... routine inspection of the material source
and of the aggregate processing plant and handling system,
all the way through to the point of batching; routine sam-
pling...
guide for precast concrete wall panels
... Editorial subcommittee
This guide presents recommendations for precast wall panels. This guide
should be used with ACI 318 “Building Code Requirements for Reinforced
Concrete which may be legally ... designing, manufacturing, and erecting precast
concrete wall panels. Although the focus is on precast
wall panels produced in established precasting plants, site
precas...
guide for the analysis, design, and construction of concrete-pedestal water towers
... 371R-5
3.1—General
3.2—Concrete
3.3—Formwork
3.4—Reinforcement
3.5—Concrete finishes
3.6—Tolerances
3.7—Foundations
3.8—Grout
Guide for the Analysis, Design, and Construction of
Concrete-Pedestal Water Towers
Reported ...
ASTM A 497 are permitted for reinforcement resisting other forces, and for shrinkage and temperature steel.
371R-1 5GUIDE FOR CONCRETE-PED...
guide for selecting proportions for high-strength concrete with portland cement and fly ash
... ACI
211.4R-93
(Reapproved 1998)
Guide for Selecting Proportions for High-Strength
Concrete with Portland Cement
and Fly Ash
Reported by ACI Committee
211
Olga Alonzo*
William ... of the
cement and fly ash.
In Tables 4.3.5(a) and
(b),
recommended maximum
w/(c+p)
are given as a function of maximum-size aggregate
HIGH-STRENGTH CONCRETE WITH PORTLAND...
guide for selecting proportions for no-slump concrete
... slump).
Fig. 3.3—Volume correction factors for dry-rodded coarse aggregate for concrete of
different consistencies.
GUIDE FOR SELECTING PROPORTIONS FOR NO-SLUMP CONCRETE 211.3R-7
plastic consistencies, ... added at mixer 141 100
GUIDE FOR SELECTING PROPORTIONS FOR NO-SLUMP CONCRETE 211.3R-9
resulting from maintaining a constant consistency, is considered
norm...
guide for submittal of concrete proportions
... all of these aggregate properties influ-
ence the proportioning of the concrete mixture, they should be
submitted to support the proposed mixture proportions.
GUIDE FOR SUBMITTAL OF CONCRETE PROPORTIONS ... selection of the appropriate
f
cr
′ . Submittal of concrete mixture proportions should con-
tain the method used to select f
cr
′ for each class of concre...
guide for the design and construction of fixed offshore concrete structures
...
B.11- Other factors
criteria
PREFACE
Concrete structures have been used in the North Sea and
other offshore areas of the world. With the rapid expansion of
knowledge of the behavior of concrete structures ... for consideration by the designer. The
design of offshore structures requires much creativity of the
designer, and it is intended that th...
guide for polymer concrete overlays
... be
evaluated for each type of damage to the overlay.
Com-
POLYMER CONCRETE OVERLAYS
548.5R-17
Table
6.1-Typical
test methods for polymer concrete overlays
Material
Binder
Aggregate
Polymer concrete
Overlay ... Strength
of Concrete
503R
Use of Epoxy Compounds with Concrete
503.5R
Guide for the Selection of Polymer Adhesives
with Concrete
546.1R
Guide for...