guide for precast concrete wall panels

... Division 3 Section “Architectural Precast Concrete. ” 2. Division 3 Section “Cast-in-Place Concrete for placing connection anchors in concrete and structural topping. 3. Division 3 Section Precast ... Owner. 23 Issue Date 9/28/04 SECTION 03410 Structural Precast Concrete PCI GUIDE SPECIFICATION FOR STRUCTURAL PRECAST CONCRETE Guide Specification Development:...

Ngày tải lên: 01/05/2014, 09:50

... particular attention for bridge decks are as follows: a. The concrete production and delivery equipment should be reviewed at the preconstruction plan- CONCRETE HIGHWAY BRIDGE DECK CONSTRUCTION 345R-9 b. c . d . e . TABLE ... Reinforcement i BOTTOM OF SLAB Fig. 2.4 Typical dimensions and tolerance for location of reinforcing steel in concrete bridge decks Fig. 2.5...

Ngày tải lên: 24/10/2014, 15:47

... and wall forms: Centrifu- gal force = 0.5 [(mass of form) + 0.2 (concrete mass)]. 2. For stiff mixtures in pipe and other rigid forms: Centrif- ugal force = 1.5 [(weight of form) + 0.2 (concrete ... consolidation of concrete by permitting place- ment with less consolidation effort. Refer to reports of ACI Committee 226 for more information regarding these mate- rials. The...

Ngày tải lên: 24/10/2014, 15:47

... areas and access for delivery vehicles. The design and construction of concrete slabs for parking lots and outside storage areas share many similarities with the design and construction of streets ... Performance and Design of GUIDE FOR DESIGN AND CONSTRUCTION OF CONCRETE PARKING LOTS 330R-21 Plain Concrete Pavement,” Highway Research Re...

Ngày tải lên: 24/10/2014, 15:47

... the bottom of the slab. If the underside of the slab is exposed to fire, the bottom of the slab will expand more than the top, resulting in a deflection of the slab. The tensile strength of the ... percent of the maximum negative mo- ment reinforcement in the span extend throughout the span FIRE ENDURANCE OF CONCRETE ELEMENTS 216R-7 Fire Fir...

Ngày tải lên: 24/10/2014, 15:47

... methods of placing concrete. 304R-1 7MEASURING, MIXING, TRANSPORTING, AND PLACING CONCRETE 5.2—Planning A basic requirement in all concrete handling is that both quality and uniformity of the concrete, ... 304R-1 5MEASURING, MIXING, TRANSPORTING, AND PLACING CONCRETE Fig. 5.2(a) to (d)—Correct and incorrect methods of placing concrete. 304R-16 ACI COMMIT...

Ngày tải lên: 24/10/2014, 15:47

... involvement before design. Concrete, structural lightweight aggregate—See concrete, structural lightweight. Concrete, structural lightweight (SLC) Structural lightweight-aggregate concrete made with structural ... successful use, and the performance of structural lightweight-aggregate concrete in service. This guide includes a definition of lightweight-aggregate con...

Ngày tải lên: 24/10/2014, 15:47

... products, specifications. CONTENTS Chapter 1—Introduction, p. 234R-2 1.1—General 1.2—What is silica fume? 1.3 Silica fume versus other forms of synthetic silica 1.4—Using silica fume in concrete 1.5—Using silica fume in blended ... is silica fume (ACI 116R). The initial interest in the use of silica fume was mainly caused by the strict enforcement...

Ngày tải lên: 24/10/2014, 15:48

... 221R-1 This guide presents information on selection and use of normal weight and heavyweight aggregates in concrete. The selection and use of aggregates in concrete should be based ... routine inspection of the material source and of the aggregate processing plant and handling system, all the way through to the point of batching; routine sam- pling...

Ngày tải lên: 24/10/2014, 15:48

... 550R-1 Recommendations for the design of precast concrete structures are pre- sented. Design of individual members and of connections for the integra- tion of members into structures are ... to provide designs for the mem- bers and/or connections. PRECAST CONCRETE STRUCTURES 550R-3 The contract documents should show the loads to be con- sidered in design of the pr...

Ngày tải lên: 24/10/2014, 17:26

... Editorial subcommittee This guide presents recommendations for precast wall panels. This guide should be used with ACI 318 “Building Code Requirements for Reinforced Concrete which may be legally ... designing, manufacturing, and erecting precast concrete wall panels. Although the focus is on precast wall panels produced in established precasting plants, site precas...

Ngày tải lên: 24/10/2014, 17:26

... 371R-5 3.1—General 3.2—Concrete 3.3—Formwork 3.4—Reinforcement 3.5—Concrete finishes 3.6—Tolerances 3.7—Foundations 3.8—Grout Guide for the Analysis, Design, and Construction of Concrete-Pedestal Water Towers Reported ... ASTM A 497 are permitted for reinforcement resisting other forces, and for shrinkage and temperature steel. 371R-1 5GUIDE FOR CONCRETE-PED...

Ngày tải lên: 24/10/2014, 17:26

... ACI 211.4R-93 (Reapproved 1998) Guide for Selecting Proportions for High-Strength Concrete with Portland Cement and Fly Ash Reported by ACI Committee 211 Olga Alonzo* William ... of the cement and fly ash. In Tables 4.3.5(a) and (b), recommended maximum w/(c+p) are given as a function of maximum-size aggregate HIGH-STRENGTH CONCRETE WITH PORTLAND...

Ngày tải lên: 24/10/2014, 17:40

... be evaluated for each type of damage to the overlay. Com- POLYMER CONCRETE OVERLAYS 548.5R-17 Table 6.1-Typical test methods for polymer concrete overlays Material Binder Aggregate Polymer concrete Overlay ... Strength of Concrete 503R Use of Epoxy Compounds with Concrete 503.5R Guide for the Selection of Polymer Adhesives with Concrete 546.1R Guide for...

Ngày tải lên: 24/10/2014, 22:11

... for Concrete Reinforcement A 615 Standard Specification for Deformed and Plain Billet- Steel Bars for Concrete Reinforcement C 33 Standard Specifications for Concrete Aggregates C 144 Standard ... portland cement slurry or hot dipped zinc coating. CHAPTER 3 CONCRETE PROPERTIES 3.1—Compressive strength Low-density concrete used in precast reinforced cellular concrete...

Ngày tải lên: 24/10/2014, 22:11