Mastercam Version 9 SolidsTutorial - Part 8 ppsx

... perspective Install/Update perspective 52 WebSphere Studio Application Developer Version 5 Programming Guide Editors When you open a file, Application Developer automatically opens the editor ... 3 -5) . Figure 3 -5 Select Perspective dialog Select the perspective you would like to open and confirm the dialog with OK . 48 WebSphere Studio Application Developer...

Ngày tải lên: 03/07/2014, 20:20

...

Ngày tải lên: 22/07/2014, 10:20

...

Ngày tải lên: 22/07/2014, 10:21

... y0 w1 h1" alt=""

Ngày tải lên: 22/07/2014, 10:21

Ngày tải lên: 06/08/2014, 11:21

... w7 h1" alt=""

Ngày tải lên: 07/08/2014, 01:21

... Connecticut, 0608 4-2 830 USA Phone (860) 87 5-5 006 Fax (860) 87 2 -1 565 BBS (860) 87 1- 8 050 TELNET and ftp:// ftp .mastercam. com or 17 2 .16 .10 0 .10 0 Internet Address http://www .mastercam. com E-mail support @mastercam. com ... edges 95 Exercise 8 – Defining the connecting rod’s weight 10 7 5 Designing a Forging Die 11 1 Exercise 1 – Setting visible leve...

Ngày tải lên: 14/08/2014, 10:22

... through all of the radius values ( 72, 144 ,28 8,480). Chapter 2 12 Mastercam Version 9 Solids Tutorial 3. Press [Alt + S] to turn on full-time shading. Your part should look like the following ... working folder: Mcam9\Tutorials\Solids Tutorial\Metric. 6. Type chair-solid-mm.mc9 for File name and choose Save. Designing a Chair Seat Mastercam Version 9 Solids Tut...

Ngày tải lên: 14/08/2014, 10:22

... 3 70 Mastercam Version 9 Solids Tutorial Designing a Plastic Cap Mastercam Version 9 Solids Tutorial 37 6. Choose OK to create the nozzle on the cap base. 7. Turn on shading. Your part ... look like the following picture. Designing a Plastic Cap Mastercam Version 9 Solids Tutorial 35 4. Save the file as cap-solid-mm.mc9 in your working folder. Exercise...

Ngày tải lên: 14/08/2014, 10:22

... Designing a Connecting Rod Mastercam Version 9 Solids Tutorial 99 14. Turn on shading. Your part should look like the following picture. Notice that the center line of the part is now rounded. ... Mastercam Version 9 Solids Tutorial 105 12. Choose OK to fillet the selected edges. 13. Turn on shading. Your part should look like the following picture. Filleting edg...

Ngày tải lên: 14/08/2014, 10:22

... Chapter 5 124 Mastercam Version 9 Solids Tutorial Chapter 5 114 Mastercam Version 9 Solids Tutorial Exercise 2 – Creating the die stock In this exercise, you will create a block-shaped ... visible levels and display lines 1. Open rod-solid-mm.mc9 from your working folder. Note: If you did not complete Chapter 4, open rod-solid-backup- mm.mc9. 2. Choose the Lev...

Ngày tải lên: 14/08/2014, 11:20

... Race Car Mastercam Version 9 Solids Tutorial 153 6. Zoom in on the end of the windshield that contains the light-blue circles. These circles represent the through-holes. Your part should ... six circles. 8. Fit the geometry to the screen. Your part should look like the following picture. 1 2 Chapter 6 1 56 Mastercam Version 9 Solids Tutorial Note: If you do...

Ngày tải lên: 14/08/2014, 11:20

... dialog box opens. 7. Enter Sprue Hole Core for the operation name. 8. Select Cut Body. 9. Select Extend through all. Chapter 7 196 Mastercam Version 9 Solids Tutorial 7. Select Extend by ... editing purposes later. Chapter 7 200 Mastercam Version 9 Solids Tutorial Designing an Injection Mold for a Camera Mastercam Version 9 Solids Tutorial 191 S p ru...

Ngày tải lên: 14/08/2014, 11:20

... then choose Done. Mastercam hides the mold core (light blue solid). Your part should look like the following picture. 17. Save the file. Chapter 8 2 28 Mastercam Version 9 Solids Tutorial ... parting surface and contains the shape of the final product (container). Chapter 8 234 Mastercam Version 9 Solids Tutorial 12. Dynamically spin the solid to see the fini...

Ngày tải lên: 14/08/2014, 11:20

... 266 Mastercam Version 9 Solids Tutorial 6. Choose OK to cut the electrode. Your part should look like the following picture. 7. Save the file. Chapter 9 262 Mastercam Version 9 Solids ... 9. Choose OK to create the electrode blank. 10. Turn on shading. Your part should look like the following picture. Chapter 9 252 Mastercam Version 9 Solids Tutoria...

Ngày tải lên: 14/08/2014, 11:20