Meshing User''''''''s Guide ANSYS phần 3 potx

... when CutCell meshing is active. Refer to The CutCell Meshing Workflow (p. 231 ) for details. Inflation AlgorithmMesh Method PostPre Yes, 3DYes, 3DPatch Conforming Tetrahedrons Yes, 3DN/APatch Independent Tetrahedrons N/AN/AHex ... following mesh methods: Volume Meshing: • Patch Conforming • Thin Solid Sweeping • Hex Dominant Meshing Surface Meshing: • Quad Dominant • All Triangles...

Ngày tải lên: 14/08/2014, 08:22

... FLUID2_2#FLUID1 _3, FLUID3_1#FLUID2_2, and FLUID3_1#FLUID4_4. • For each body in the ANSYS Workbench file (fluid1, fluid2, fluid3, fluid4), a Material Point has been as- signed (FLUID1 _3_ MATPOINT, ... of a part in ANSYS Workbench and a part in ANSYS ICEM CFD is not the same. For information about parts in ANSYS Workbench, refer to Conformal Meshing Between Parts (p. 7) in the M...

Ngày tải lên: 14/08/2014, 08:22

... mesh on the left, a Pinch Tolerance of 3e -3 and a Min Size of 6.e -3 were specified. For the mesh on the right, a Pinch Tolerance of 3e -3 and a Min Size of 4.e -3 were specified. Neither is acceptable ... elements are displayed in the Geometry window. 1 03 Release 13. 0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its sub...

Ngày tải lên: 14/08/2014, 08:22

... affiliates. ANSYS Meshing User's Guide Table of Contents Capabilities in Workbench 1 Meshing Overview 1 Meshing Implementation in ANSYS Workbench 3 Types of Meshing 4 Meshing by Algorithm 4 Meshing ... 227 CutCell Meshing 228 The CutCell Meshing Process 228 The CutCell Meshing Workflow 231 Direct Meshing 239 Inflation Controls 244 Mesh Refinement 250 Mixed O...

Ngày tải lên: 14/08/2014, 08:22

... fillet/chamfer. Notice the angles in the figure below. 133 Release 13. 0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates. Setting ... re -meshing during the meshing process. If Use Advanced Size Function (p. 59) is off: Release 13. 0 - © SAS IP, Inc. All rights reserved. - Contains proprietary a...

Ngày tải lên: 14/08/2014, 08:22

... Order Meshing Air Gap Meshing Contact Meshing Winding Body Meshing Wire Body Meshing Pyramid Transitions Match Meshing and the Symmetry Folder Rigid Body Meshing Thin Solid Meshing CAD Instance Meshing Meshing ... Grid Lines Vertex Type 0° — 135 °0End 136 ° — 224°1Side 225° — 31 4°2Corner 31 5° — 36 0° (You cannot specify Reversal vertices.The range for Reversal vertices...

Ngày tải lên: 14/08/2014, 08:23

... Controls (p. 2 63) (Patch Inde- pendent Mesh Methods table). CutCell Meshing CutCell Cartesian meshing is a general purpose meshing method designed for ANSYS FLUENT. The CutCell meshing algorithm ... the Mechanical Model system. CutCell meshing topics include: The CutCell Meshing Process The CutCell Meshing Workflow The CutCell Meshing Process The CutCell meshing process i...

Ngày tải lên: 14/08/2014, 08:23

... Rigid Body Contact Meshing Using 3D Rigid Body Contact Meshing This section describes the basic steps for using 3D rigid body contact meshing. To define a 3D rigid body for contact meshing: 1. Open ... body. Figure: Direct Meshing: Right Body First Disabling Direct Meshing Set the Allow Direct Meshing option to No to disable direct meshing. The Meshing application behaves as f...

Ngày tải lên: 14/08/2014, 08:23

... (p. 101). • Refer to Direct Meshing (p. 239 ) for general information about direct meshing and limitations related to using the Preview Inflation feature with direct meshing. To preview inflation: 1. ... Thin). • Refer to Direct Meshing (p. 239 ) for general information about direct meshing and limitations related to using the Preview Source and Target Mesh feature with direct mes...

Ngày tải lên: 14/08/2014, 08:23

... 50 workflow, 3 workflow - basic meshing, 11 workflow - CFD meshing, 12 workflow - combining CFD/fluids and structural meshing, 13 workflow - Fluids meshing, 12 Meshing application basic meshing workflow, ... 11 Meshing application - basic workflow for CFD, 12 Meshing application - basic workflow for combining CFD/fluids and structural meshing, 13 Meshing application - basic...

Ngày tải lên: 14/08/2014, 08:23