Basic Analysis Guide ANSYS phần 10 pdf

... command, 108 RITER command, 108 RLIST command, 3 RMEMRY command, 108 rotating results, 181 RSPEED command, 108 RSPLIT, 192 RSTAT command, 108 RSTMAC, 194 RTIMST command, 108 run time estimation, 107 /RUNSTAT ... controls dialog box, 108 109 solution results, displaying as vectors, 258 SOLVE command, 115 solver memory, 104 solver performance, 104 solvers, 99 Algebraic Multi...

Ngày tải lên: 14/08/2014, 06:22

... Electromagnetic Analysis Guide. • Example problems in the High-Frequency Electromagnetic Analysis Guide. • Example: Structural-Thermal Harmonic Analysis in the Coupled-Field Analysis Guide. Release ... information of ANSYS, Inc. and its subsidiaries and affiliates. Basic Analysis Guide Table of Contents 1. Getting Started with ANSYS 1 1.1. Building the Model 1 1.1.1. Sp...

Ngày tải lên: 14/08/2014, 06:22

... Y-Dim *taxis,ccc(1,1,1,1,1),3,1,2,3,4,5,6,7,8,9 ,10 !!! Z-Dim *taxis,ccc(1,1,1,1,1),4,0 ,10, 20,30,40 !!! Time *taxis,ccc(1,1,1,1,1),5,0,50 ,100 ,150,200 !!! Temp *do,ii,1,2 *do,jj,1,2 *do,kk,1 ,10 *do,ll,1,5 *do,mm,1,5 ... specifies a heat flux of 100 on all selected nodes. If nodes 1 through 4 are part of the selected set, those nodes are assigned heat fluxes of 100 + ABC(i): 100 +...

Ngày tải lên: 14/08/2014, 06:22

... Damping Specifies transient analysis options TRNOPT Main Menu> Preprocessor> Loads> Analysis Type> Analysis Options Main Menu> Preprocessor> Loads> Analysis Type> New Analysis Main ... /post1 plnsol,s,z 2.8.4. Example Pretension Analysis (GUI Method) This section presents a sample pretension analysis using the ANSYS GUI. 2.8.4.1. Set the Analysis T...

Ngày tải lên: 14/08/2014, 06:22

... Jobname.RST for a structural analysis • Jobname.RTH for a thermal analysis • Jobname.RMG for a magnetic field analysis • Jobname.RFL for a FLOTRAN analysis For a FLOTRAN analysis, the file extension ... 1 are in the database. NSEL,S,NODE,,6 ,10 ! Select nodes 6 to 10 APPEND,2 ! Merge data from load step 2 into database NSEL,S,NODE,,1 ,10 ! Select nodes 1 to 10 PRNSOL,DOF ! Prin...

Ngày tải lên: 14/08/2014, 06:22

... the Structural Analysis Guide • "Transient Dynamic Analysis& quot; in the Structural Analysis Guide • "Nonlinear Structural Analysis& quot; in the Structural Analysis Guide 5.5. Using ... processors for a single ANSYS job. See "Using Shared-Memory ANSYS& quot; in the Advanced Analysis Techniques Guide or the Distributed ANSYS Guide for more information...

Ngày tải lên: 14/08/2014, 06:22

... Advanced Analysis Techniques Guide. 7.4.5. Creating or Modifying Results Data in the Database You can do postprocessing without ever producing an ANSYS results file. All you need to do is create an ANSYS ... data from your analysis in the graphics window. This selection is grayed out when only real data exists for your analysis. Imaginary Data - You can display the imaginary data...

Ngày tải lên: 14/08/2014, 06:22

... confidential information of ANSYS, Inc. and its subsidiaries and affiliates. 10. 4.4. Displaying X11 Graphics over Networks Chapter 10: Getting Started with Graphics The ANSYS program (and the associated ... External Graphics 10. 2. Identifying the Graphics Device Name (for UNIX) 10. 3. Specifying the Graphics Display Device Type (for Windows) 10. 4. System-Dependent Graphics Informat...

Ngày tải lên: 14/08/2014, 06:22

... LD_LIBRARY_PATH /ansys_ inc/v120 /ansys/ syslib/usparc: /ansys_ inc/v120 /ansys/ lib/usparc:/usr/lib For 64 bit: setenv OPENWINHOME path/openwin setenv LD_LIBRARY_PATH /ansys_ inc/v120 /ansys/ syslib/sun64: /ansys_ inc/v120 /ansys/ lib/sun64:/usr/lib Note You ... licensed software, OpenGL. 10. 4.9. Silicon Graphics Drivers Both X11 and SGI OpenGL graphics drivers are supported on the Silic...

Ngày tải lên: 14/08/2014, 06:22

... applications outside of the ANSYS program. Of special interest is the .GRPH file, a neutral graphics file that uses the ANSYS plotting instructions to recreate the file in applications other than ANSYS. Note The ... the ANSYS log file.The report generator also writes the ansys: :report::interpdynamicdata com- mand to the log file; the command must process the HTML code in order for t...

Ngày tải lên: 14/08/2014, 06:22