Basic Analysis Guide ANSYS phần 4 pps

... 0.00000 , -2. 042 04 1, 2, 1, 1, 3.50063 , 0.607255E-01, 0.0000 , -2. 042 04 1, 3, 1, 1, 3.50063 , 0.607255E-01, 0.00000 , 2. 042 04 1, 4, 1, 1, -3.50063 , -23.2768 , 0.00000 , 2. 042 04 /csys,0 ... Static Analysis& quot; in the Structural Analysis Guide • "Transient Dynamic Analysis& quot; in the Structural Analysis Guide • "Nonlinear Structural Analysis& q...

Ngày tải lên: 14/08/2014, 06:22

... explicitly modeled. To perform a multibody analysis, the pin geometry is ignored and the behavior replaced by the appropriate MPC1 84 joint element. Figure 2. 14: Pinned Joint Geometry Figure 2.15: ... confidential information of ANSYS, Inc. and its subsidiaries and affiliates. 28 Chapter 2: Modeling in a Multibody Simulation Chapter 3: Performing a Multibody Analysis A multibody in ANS...

Ngày tải lên: 14/08/2014, 09:20

... 8 1.1 .4. 4.2. Choosing Material Behavior 8 1.1 .4. 4.3. Entering Material Data 9 1.1 .4. 4 .4. Logging/Editing Material Data 12 1.1 .4. 4.5. Example: Defining a Single Material Model 12 1.1 .4. 4.6. Example: ... Drive ANSYS, Inc. is certified to ISO 9001:2008. Canonsburg, PA 15317 ansysinfo @ansys. com http://www .ansys. com (T) 7 24- 746 -33 04 (F) 7 24- 5 14- 949 4 2.20. Pretension Defin...

Ngày tải lên: 14/08/2014, 06:22

... example: F ,44 7,FY,3000 ! Applies FY = 3000 at node 44 7 F ,44 7,FY,2500 ! Changes FY value to 2500 (replacement) FCUM,ADD ! Subsequent F's to be added F ,44 7,FY,-1000 ! FY = 2500-1000 = 1500 at node 44 7 FCUM,IGNORE ... 2.16: Concentrated Axisymmetric Loads (p. 48 )), the total load of 47 ,1 24 lb. (1500*2 π*5 = 47 ,1 24) would be applied to node N as follows: F,N,FY, -47 1 24...

Ngày tải lên: 14/08/2014, 06:22

... solve /post1 plnsol,s,z 2.8 .4. Example Pretension Analysis (GUI Method) This section presents a sample pretension analysis using the ANSYS GUI. 2.8 .4. 1. Set the Analysis Title 1. Select Utility ... State Application 4. 4. Initial State File Format 4. 5. Using Coordinate Systems with Initial State 4. 6. Example Problems Using Initial State 4. 7.Writing Initial State Values...

Ngày tải lên: 14/08/2014, 06:22

... 0 JIEItemLabel 82-SMISCMFORY 93-SMISCMFORZ 1 04- SMISCMMOMX 115-SMISCMMOMY 126-SMISCMMOMZ 141 3-SMISCP1 1615-SMISCOFFST1 1817-SMISCP2 2019-SMISCOFFST2 2221-SMISCP3 242 3-SMISCOFFST3 -25-SMISCP4 26 SMISCP5 Pseudo Node 876 543 21 876 543 21LBFETEMP For ... 2 (J) 0.00000E+00 1 04. 00 -1 04. 00 LOCATION SMAX SMIN 1 (I) 130.00 -130.00 2 (J) 1 04. 00 -1 04. 00 LOCATION EPELDIR EPELBYT E...

Ngày tải lên: 14/08/2014, 06:22

... ABC ABC2 1 .21676 .43 351 11 .27032 . 540 64 21 .23686 .47 372 31 .47 783 .95565 41 .36171 .72 341 51 .36693 .73387 61 .13081 .26162 71 .50835 1.0167 81 .350 24 .70 049 91 .25630 .51260 ... 51 -1.0 147 97795 98530 .17839E-01 .00000E+00 .00000E+00 41 -1.0379 -1.0677 -1. 041 8 50 042 E-01 .00000E+00 .00000E+00 31 -1. 040 6 9 943 0 -1.0110 .1 042 5E-01 .00000E+00 .00000...

Ngày tải lên: 14/08/2014, 06:22

... ***** ANSYS time-history VARIABLE LISTING ***** TIME 51 UX 30 UY UX UY .10000E-09 .000000E+00 .000000E+00 .32000 .106832 .371753E-01 .42 667 . 146 785 .620728E-01 . 746 67 .263833 . 144 850 ... shell results ESOL ,4, 20,23,S,X ! Variable 4 = bottom SX at node 23 of element 20 STORE ! By command default, place variable 4 in memory with 2 and 3 PLVAR,2,3 ,4 ! Plot variables 2,3...

Ngày tải lên: 14/08/2014, 06:22

... LD_LIBRARY_PATH /ansys_ inc/v120 /ansys/ syslib/usparc: /ansys_ inc/v120 /ansys/ lib/usparc:/usr/lib For 64 bit: setenv OPENWINHOME path/openwin setenv LD_LIBRARY_PATH /ansys_ inc/v120 /ansys/ syslib/sun 64: /ansys_ inc/v120 /ansys/ lib/sun 64: /usr/lib Note You ... confidential information of ANSYS, Inc. and its subsidiaries and affiliates. 2 54 Chapter 13: Creating Geometry Displays Fi...

Ngày tải lên: 14/08/2014, 06:22

... Strain40 Shear Thermal Strain41 Principal Thermal Strain42 Thermal Strain Intensity and Thermal Equivalent Strain43 Component Pressure Gradient and Sum 44 Component Electric Field and Sum45 Release ... ANSYS command to issue to generate the output text. 4. Click on the OK button. Result: The report generator issues this report command to the ANSYS program and saves the listing: ~eui,&ap...

Ngày tải lên: 14/08/2014, 06:22